Washer Repair in Winston-Salem, NC
Washer repair in Winston-Salem runs a median of $331 once a part is fitted, with the middle half of jobs between $300 and $389. That comes from 35 washer jobs across seven ZIP codes in 34 separate households, 26 paid visits, 12 of which ended with a component replaced.
Nine of the twelve work orders name the part, and five of those nine are the same fault: a drum that will not stay still. What makes this city worth reading is that the same fault has two different parts and two different prices, depending on whether the machine loads from the top or the front.
Washer Repair in Winston-Salem — Top-Load, Front-Load and Stacked
Mobile service across every Winston-Salem ZIP code with no travel charge inside the city. The $99 diagnostic is applied to the repair once you approve it, $150 on a stacked washer-dryer because two machines share one cabinet, and the price for the whole job is fixed before any work starts.
All Twelve Winston-Salem Invoices, With the Part Named
| What was replaced | Winston-Salem invoice | Machine type | Company median |
|---|---|---|---|
| Door lock adjusted | $249 | — | $351 lock or lid switch |
| Rewiring, Kenmore | $259 | top-load | — |
| Maintenance and service, Samsung | $300 | front-load | — |
| Suspension rods, all four, Maytag | $319 | top-load | $367 |
| Suspension rods, Whirlpool | $342 | top-load | $367 |
| Shock absorbers, three, LG | $363 | front-load | $367 |
| Suspension, Samsung | $389 | top-load | $367 |
| Water inlet valve, Samsung | $394 | — | $362 |
| Shock absorbers, three, GE | $457 | front-load | $367 |
| Part not named on the work order | $269 · $308 · $364 | — | — |
| All Winston-Salem washer repairs with a part | $331 median, 12 jobs | — | $370 across 4,763 |
| Diagnostic visit | $99 | — | $99 |
Why Winston-Salem Washer Work Looks the Way It Does
Five of nine named parts steady the drum AGAINST 4.8 PERCENT COMPANY-WIDE
Suspension rods on three top-loaders and shock absorbers on two front-loaders. Company-wide, shock and suspension work is 195 of 4,763 washer repairs — 4.8 percent, well behind drain pumps and door locks. In this city it is more than half of everything we can name.
Those parts are what stop the drum swinging, and they wear faster on a machine that is out of level, on a suspended or springy floor, and on loads that go in as one heavy wet mass on one side of the drum.
Tell us at booking whether the machine has started walking or thumping on the spin cycle, because that is the single most likely repair here and the technician will bring the parts.
Both cheapest repairs were adjustments, not replacements $249 AND $259
The two lowest invoices in this city were a door lock adjustment at $249 and rewiring on a Kenmore top-loader at $259 — neither of them a new component. Company-wide a door lock or lid switch replacement is $351, so the adjustment saved about a hundred dollars over swapping the part.
That is worth knowing when someone tells you a washer that will not start needs a new lock: sometimes it needs the existing one set right. It is also why we quote after the machine is opened rather than over the phone.
Maytag leads and GE is close behind 7 AND 6 OF 30 BRANDED
Thirty of the 35 jobs name a brand: Maytag 7, GE 6, Samsung 6, Whirlpool 5, LG 4, Kenmore 2. Company-wide our washer work runs Whirlpool 21.6 percent, GE 19.7, Samsung 19.2, Maytag 11.0 and LG 8.4 across 8,320 jobs — so Winston-Salem carries roughly double the Maytag share and about half again the LG share.
The front-load shock jobs were an LG and a GE, and all three suspension-rod jobs were top-loaders from Maytag, Whirlpool and Samsung. As always this is a picture of what is installed in local laundry rooms and who gets called to it, not a ranking of which brand lasts longest.
The southwest and southeast carry the work 16 OF 35
27103 has nine jobs and four component repairs, 27107 seven and three. After those: 27106 six, 27104 five, 27127 four, 27105 three, 27101 one — and the single 27101 job did end with a part. Every one of the 35 jobs is a different household bar one, so nothing on this page is inflated by one difficult machine visited repeatedly.
And every work order dates from March 2026, when the route opened, which is why this page publishes an invoice list rather than a seasonal claim.
Three details are worth telling us at booking, because each one changes what the technician puts on the van: whether the machine loads from the top or the front, whether it is stacked, and whether it has started moving across the floor on spin. The first two decide which suspension parts to bring, and the third is the most likely repair in this city.
Match Your Symptom to the Likely Cause
- Walking across the floor, thumping or banging on spin — the most common named repair in this city. On a top-loader it is the suspension rods, $319 to $389 locally against a company $367. On a front-loader it is the shock absorbers, $363 and $457 locally. Mention the machine type at booking and the right parts come with the technician.
- Will not drain, water standing in the drum — the drain pump, our most-replaced washer part company-wide at $381 across 213 repairs, or a restriction in the drain hose which the technician clears on the visit. Company median for the symptom is $377 across 508 jobs.
- Will not spin, clothes come out soaking — door lock or lid switch at a company $351, the drive belt at $341, or the motor at $387. Winston-Salem produced a lock adjustment at $249 rather than a replacement, which is the cheaper outcome.
- Leaking underneath — on a front-loader usually the door boot seal at a company $450; on a top-loader a hose or the water inlet valve, and our one local valve job was $394. Company median for a leak call is $354 across 482 jobs.
- Will not start, no lights, dies mid-cycle — the door lock, or the motor control board at $436. Company median for the symptom is $376 across 103 jobs. Worth noting the lock is both the cheaper and the commoner of the two.
- Error code on the display — write it down before you call, because it narrows the visit considerably. Company median for a coded fault is $385 across 492 jobs, and a water-supply code often turns out to be a half-open tap or a blocked inlet screen rather than a part.
- Grinding or roaring that worsens through the cycle — bearing or basket, at a company $380. This is the one washer repair where the arithmetic genuinely turns on an older top-loader, because the labour rather than the part does the damage, and we will put both figures in front of you.
Winston-Salem Washer Work by ZIP Code
| ZIP | Area | Jobs | Paid visits | Part fitted |
|---|---|---|---|---|
| 27103 | Southwest Winston-Salem | 9 | 7 | 4 |
| 27107 | Southeast Winston-Salem | 7 | 6 | 3 |
| 27106 | Northwest Winston-Salem | 6 | 4 | 1 |
| 27104 | West Winston-Salem | 5 | 4 | 2 |
| 27127 | South Winston-Salem | 4 | 3 | 1 |
| 27105 | Northeast Winston-Salem | 3 | 1 | 0 |
| 27101 | Downtown and central | 1 | 1 | 1 |
Winston-Salem is the county seat of Forsyth County and the second city of the Piedmont Triad. Seven ZIP codes appear in our washer book and all are covered at the same rate, with no travel charge inside the city. We work as a mobile service here: the technician comes to the laundry room, and there is no counter or depot to bring a machine to.
Washer Brands We Are Called To in Winston-Salem
| Brand | Winston-Salem washer jobs | Company share of washer work |
|---|---|---|
| Maytag | 7 | 11.0 percent |
| GE | 6 | 19.7 percent |
| Samsung | 6 | 19.2 percent |
| Whirlpool | 5 | 21.6 percent |
| LG | 4 | 8.4 percent |
| Kenmore | 2 | — |
| Branded jobs | 30 of 35 | 8,320 company washer jobs |
We also service KitchenAid, Bosch, Amana, Electrolux, Frigidaire, Speed Queen and Haier washers here, top-load and front-load, freestanding and stacked. On a stacked washer-dryer the diagnostic is $150 rather than $99, because two machines share one cabinet and both have to be assessed to establish which has failed.
Repair or Replace, in Winston-Salem Numbers
A Winston-Salem washer repair has a middle value of $331 and, across twelve invoices, a ceiling of $457. A new mid-range top-loader is $500 to $900 fitted and a front-loader $700 to $1,400, with large-capacity and stacked units above that.
Against those figures a $319 set of suspension rods, a $249 lock adjustment or even a $457 set of front-load shocks is between a third and a half of a replacement, and none of them touches the tub or the cabinet.
Two repairs deserve a pause rather than a signature. A bearing or basket failure at a company median of $380 involves stripping most of the machine, and on an older top-loader the labour hour rather than the part is doing the spending. A motor control board at $436 on a machine already past ten years is the same conversation.
In both cases we set the repair figure beside a realistic replacement figure at the assessment, before anything is dismantled. Typical service lives are on how long washing machines last, the balance and levelling side on washing machine out of balance, error codes on washing machine error codes, and the break-even arithmetic in the repair versus replacement guide.
Discounts Applied Automatically
Priority Membership
$179 a year — five diagnostics, priority slots
- Five free diagnostic visits a year, a $495 value
- Priority scheduling with 24 to 48 hour response
- $30 off labor on every repair
- Extended warranty on all Bozmanfix work
What Customers Say About Our Washer Work
“Alex was amazing — timely, professional, and he quickly identified the problem with our washer. He went above and beyond. 10/10.”
“Alex came, assessed my issue, had the part on him, and fixed the problem all in 45 minutes. I’m loading my washer before he even left the driveway! Highly recommend!”
“Yuriy did an excellent job repairing our washing machine.”
“Denis fixed my washer and he was top notch! Perfect gentleman and absolute professional!”
Washer Repair in Winston-Salem — Questions We Get
How much does washer repair cost in Winston-Salem?
The median is $331 once a part is fitted, from 12 component repairs among 35 Winston-Salem washer jobs, with the middle half between $300 and $389. The twelve invoices were $249, $259, $269, $300, $308, $319, $342, $363, $364, $389, $394 and $457.
By part, locally: door lock adjusted $249, rewiring $259, maintenance $300, top-load suspension rods $319, $342 and $389, front-load shock absorbers $363 and $457, water inlet valve $394.
Each figure includes the part, the labour and the service call. Our company washer median is $370 across 4,763 repairs. The diagnostic itself is $99, or $150 on a stacked unit.
Why do front-loaders cost more to steady than top-loaders?
Different parts and different access. A top-loader hangs its tub on four suspension rods that can be replaced as a set from above, and our three local jobs of that kind were $319, $342 and $389. A front-loader carries its drum on shock absorbers bolted into the frame, and reaching them means opening the cabinet from the front or the back — our two local jobs were $363 and $457.
The company median for the whole category is $367 across 195 repairs, so top-load rods here sit under it and front-load shocks over it. Same symptom, different hour of labour.
My washer is banging and moving across the floor. What is it?
Almost certainly the suspension — rods on a top-loader, shock absorbers on a front-loader — and it is the most common named repair in our Winston-Salem book, five of nine invoices that name a part. Locally $319 to $457 depending on machine type.
Tell us at booking whether the machine loads from the top or the front and whether it sits level on all four feet, because an out-of-level cabinet both produces the symptom and wears the parts out early, and the technician will level it as part of the repair.
Does a washer that will not start always need a new lock?
No, and this city has a good example. Our cheapest local invoice, $249, was a door lock adjusted rather than replaced — against a company median of $351 for a lock or lid switch replacement. A second job at $259 was rewiring on a Kenmore top-loader, again not a new part.
That is roughly a hundred dollars saved in each case, and it is the reason we assess the machine before quoting rather than pricing a part over the phone.
Water is sitting in the drum. Is that expensive?
Usually not. The drain pump is our most-replaced washer part company-wide, at a median of $381 across 213 repairs, and the company median for a will-not-drain call overall is $377 across 508 jobs.
Before the pump the technician checks the drain hose and the filter, because a kink or a hose pushed too far into the standpipe produces the same symptom and is corrected on the visit. Mention at booking if the machine or the plumbing has been moved recently.
Which washer brands do you service here?
The local book names Maytag seven times, GE and Samsung six each, Whirlpool five, LG four and Kenmore twice, out of 30 branded jobs in 35. We also service KitchenAid, Bosch, Amana, Electrolux, Frigidaire, Speed Queen and Haier. Winston-Salem carries about double the Maytag share of our company-wide washer work.
Where that matters to you is parts: Whirlpool, Maytag and GE suspension kits, pumps and belts are commonly on the van or next-day, while some LG and Samsung assemblies are ordered in.
Do you charge more for a stacked washer-dryer?
The diagnostic is $150 rather than $99, because a stacked or combination unit is two machines sharing one cabinet and both have to be assessed to find which has failed.
Everything after that is identical: the diagnostic is applied to the repair when you approve it, the 90-day parts and labour warranty applies, and the veteran, senior and new-customer discounts work the same way. Tell us at booking so the right length of visit is scheduled.
How long has Bozmanfix been working in Winston-Salem?
Since March 2026. All 146 Winston-Salem work orders on our books, including these 35 washer jobs, date from then, which is why this page publishes an invoice list rather than a seasonal claim — five months is not enough history to say which month washers fail in this city. The company medians quoted throughout come from more than 66,000 jobs across eight metro areas.
Other Appliance Repair in Winston-Salem
The rest of our Winston-Salem coverage, with the local job counts behind each page.
Appliance Repair in Winston-Salem — city hub, all six machines Serving Winston-Salem and the wider Charlotte area → View our full service areaBook Washer Repair in Winston-Salem
35 washer jobs on record since March 2026 across 34 households, at a median of $331 with a part fitted, and all twelve invoices published on this page. Top-load, front-load and stacked. Every ZIP code covered, no travel charge inside the city, 90-day parts and labour warranty.