Washer Repair in High Point, NC
Washer repair in High Point runs a median of $304 once a part is fitted, with the middle half of jobs between $290 and $349. That comes from 24 washer jobs in 24 separate households, 14 paid visits and six ending with a component repair.
Five of the six name the work, and the striking thing is that no two are alike: a front-load door gasket adjusted, a drain pump rewired, a pulley and belt replaced, a water supply tap changed, and a direct-drive coupling. Not one is an electronic module, and two of the five were put right in place rather than swapped out. Our company washer median is $370 across 4,763 repairs.
Washer Repair in High Point — Top-Load, Front-Load and Stacked
Mobile service across every High Point ZIP code with no travel charge inside the city. The $99 diagnostic is applied to the repair once you approve it, $150 on a stacked washer-dryer because two machines share one cabinet, and the price for the whole job is fixed before any work starts.
All Six High Point Invoices, With the Work Named
| What the visit did | High Point invoice | Company median | Company n |
|---|---|---|---|
| Front-load door gasket adjusted, LG | $249 | $450 boot seal replaced | 49 |
| Part not named on the work order | $290 | — | — |
| Drain pump rewired, Whirlpool | $290 | $381 pump replaced | 213 |
| Pulley and belt, GE | $318 | $341 drive belt | 74 |
| Water supply tap replaced, Whirlpool | $349 | $362 inlet valve | 137 |
| Direct-drive coupling, Kenmore | $363 | $387 drive motor | 81 |
| Motor control board | none yet | $436 | 163 |
| All High Point washer repairs with a part | $304 median, 6 jobs | $370 | 4,763 |
| Diagnostic visit | $99 | $99 | 8 of 14 paid |
Why High Point Washer Work Looks the Way It Does
Five repairs, five different mechanisms, nothing electronic NO BOARD IN 24 JOBS
A door seal, a drain pump connection, a drive belt and pulley, a water supply tap, a direct-drive coupling. Company-wide the motor control board is 163 of 4,763 washer repairs at a median of $436 — a routine enough job that most of our city pages have at least one.
High Point has none in 24 visits. Everything this city has produced is mechanical, and mechanical parts on a washer are the cheap end: our five named jobs run $249 to $363 where the board alone would be $436. Six invoices cannot prove a pattern, and we are not going to claim one, but it is the honest reason the local median sits $66 under our company figure.
One job was plumbing rather than appliance $349 SUPPLY TAP
One of the six replaced the water supply tap feeding a Whirlpool, not a part inside the machine. We are naming it because it belongs in a different category in your head: a washer that fills slowly or throws a supply error is often being starved by a half-seized tap or a kinked inlet hose, and no part inside the cabinet will fix that.
Company-wide the inlet valve — the equivalent part inside the machine — runs $362 across 137 repairs, so the two sit close in price and a long way apart in cause. It is worth mentioning at booking if the machine has ever been moved or the taps replaced.
Every single work order names a brand 24 OF 24
That happens on no other page in this cluster: Greensboro named 40 of 45 washers, Winston-Salem 30 of 35. Here it is all of them — Whirlpool 8, GE 6, Maytag 3, then Samsung, LG and Amana on two each and one Kenmore. Company-wide our washer work runs Whirlpool 21.6 percent, GE 19.7, Samsung 19.2, Maytag 11.0 and LG 8.4 across 8,320 jobs, so Whirlpool and GE lead both books.
Practically it means parts availability is good here: Whirlpool, GE and Maytag belts, pumps, couplings and suspension kits are commonly on the van or next-day. It is a map of what is installed, not a ranking of what lasts.
27265 holds most of the work and 27260 converts best 14 OF 24
Fourteen of the 24 washer jobs sit in 27265, producing three of the six repairs. But 27260 is the efficient one: three jobs, three paid visits, two repairs. After that 27262 has three jobs with one repair, 27263 three with none, and a single job in 27235.
Across all appliances 27265 holds 43 of our 72 High Point work orders, so the concentration is citywide rather than a washer effect. And every High Point work order dates from March 2026, when the route opened, which is why this page publishes an invoice list rather than a trend.
Three details are worth telling us at booking, because each changes what the technician puts on the van: whether the machine loads from the top or the front, whether it is stacked, and whether the fault is filling, draining or spinning. Filling problems are often upstream of the machine entirely, which is the cheapest outcome on this page.
Match Your Symptom to the Likely Cause
- Fills slowly, or throws a water supply error — check upstream first: our one local job of this kind replaced the supply tap for $349, not a part inside the machine. Inside the cabinet the equivalent is the inlet valve at a company $362 across 137 repairs.
- Will not drain, water standing in the drum — the drain pump, our most-replaced washer part company-wide at $381 across 213 repairs. Our local job rewired the pump connection instead for $290, which is what happens when the pump itself is sound. Company median for the symptom is $377 across 508 jobs.
- Leaking from the door on a front-loader — the door boot seal, $450 company-wide across 49 repairs, or a seal sitting out of true, which is what our $249 local job turned out to be. Coins and grit trapped in the fold are the usual cause of a seal that fails early.
- Will not spin, clothes come out soaking — the drive belt and pulley at $318 locally against a company $341, the direct-drive coupling at $363 locally, the door lock at $351, or the motor at $387. Company median for the symptom is $362 across 384 jobs.
- Walking across the floor, thumping on spin — suspension rods on a top-loader or shock absorbers on a front-loader, at a company median of $367 across 195 repairs. High Point has not produced one of these yet, though it is the leading repair in both other Triad cities.
- Will not start, no lights, or dies mid-cycle — the door lock at a company $351 or the motor control board at $436. No board job has come up in this city.
- Grinding or roaring that worsens through the cycle — bearing or basket, at a company $380. The one washer repair where the arithmetic genuinely turns on an older top-loader, because the labour rather than the part does the spending, and we will put both figures in front of you.
High Point Washer Work by ZIP Code
| ZIP | Area | Jobs | Paid visits | Part fitted |
|---|---|---|---|---|
| 27265 | North and west High Point | 14 | 8 | 3 |
| 27260 | Central and south High Point | 3 | 3 | 2 |
| 27262 | Central and west High Point | 3 | 1 | 1 |
| 27263 | Southeast High Point | 3 | 2 | 0 |
| 27235 | Northeast of the city | 1 | 0 | 0 |
High Point sits across Guilford, Davidson, Randolph and Forsyth counties and is the third city of the Piedmont Triad. Five ZIP codes appear in our washer book, including 27235 outside the city proper, and all are covered at the same rate with no travel charge inside the city.
We work as a mobile service: the technician comes to the laundry room, and there is no counter or depot to bring a machine to.
Washer Brands We Are Called To in High Point
| Brand | High Point washer jobs | Company share of washer work |
|---|---|---|
| Whirlpool | 8 | 21.6 percent |
| GE | 6 | 19.7 percent |
| Maytag | 3 | 11.0 percent |
| Samsung | 2 | 19.2 percent |
| LG | 2 | 8.4 percent |
| Amana | 2 | — |
| Kenmore | 1 | — |
| Branded jobs | 24 of 24 — every work order | 8,320 company washer jobs |
We also service KitchenAid, Bosch, Electrolux, Frigidaire, Speed Queen and Haier washers here, top-load and front-load, freestanding and stacked. On a stacked washer-dryer the diagnostic is $150 rather than $99, because two machines share one cabinet and both have to be assessed to establish which has failed.
Repair or Replace, in High Point Numbers
A High Point washer repair has a middle value of $304 and, across six invoices, a ceiling of $363. A new mid-range top-loader is $500 to $900 fitted and a front-loader $700 to $1,400, with large-capacity and stacked units above that.
Against those figures every repair this city has produced is between a quarter and a half of a replacement, and none of them touched the tub or the cabinet — which are the parts that actually decide how long the machine lasts.
Two repairs would change that arithmetic and neither has appeared here yet. A bearing or basket failure at a company median of $380 means stripping most of the machine, and on an older top-loader the labour hour rather than the part is doing the spending.
A motor control board at $436 on a machine already past ten years is the same conversation. In both cases we set the repair figure beside a realistic replacement figure at the assessment, before anything is dismantled.
Typical service lives are on how long washing machines last, balance and levelling on washing machine out of balance, error codes on washing machine error codes, and the break-even arithmetic in the repair versus replacement guide.
Discounts Applied Automatically
Priority Membership
$179 a year — five diagnostics, priority slots
- Five free diagnostic visits a year, a $495 value
- Priority scheduling with 24 to 48 hour response
- $30 off labor on every repair
- Extended warranty on all Bozmanfix work
What Customers Say About Our Washer Work
“Washer wasn’t spinning during the final cycle. They scheduled Technician Rick — listen to how that washer purrs now.”
“Yuriy fixed our washer so quick and works great!!! Thank you!!”
“Eugene came out to take a look at our washer. He fixed it on the spot. He was professional, quick, and easy.”
“Nick was great and able to come the same day I called to fix my washing machine. He had the part I needed and fixed the issue with no problem.”
Washer Repair in High Point — Questions We Get
How much does washer repair cost in High Point?
The median is $304 once a part is fitted, from six component repairs among 24 local washer jobs, with the middle half between $290 and $349. The six invoices were $249, $290, $290, $318, $349 and $363. By work, locally: front-load door gasket adjusted $249, drain pump rewired $290, pulley and belt $318, water supply tap replaced $349, direct-drive coupling $363.
Each figure includes the part, the labour and the service call. Our company washer median is $370 across 4,763 repairs. The diagnostic itself is $99, or $150 on a stacked unit.
You adjusted a door seal instead of replacing it. How often is that possible?
Often enough that it is worth having the machine assessed rather than ordering the part. Our local job adjusted a front-load door gasket for $249, where replacing the boot seal costs $450 company-wide across 49 repairs. A seal that is sitting out of true leaks exactly like a seal that has failed, and only one of those needs a new part.
The same happened with a drain pump here: rewired for $290 rather than replaced at the company figure of $381. Two of our five named High Point jobs were repairs in place rather than swaps.
My washer fills very slowly. Is that the valve?
It might be upstream of the machine entirely. One of our six High Point jobs replaced the water supply tap for $349 rather than anything inside the cabinet — a half-seized tap or a kinked inlet hose starves the machine and produces the same slow fill and the same supply error code as a failed inlet valve.
Inside the machine the valve runs $362 company-wide across 137 repairs. Mention at booking whether the machine or the taps have been moved or worked on recently.
Water is sitting in the drum and it will not drain. Is that expensive?
Usually not. The drain pump is our most-replaced washer part company-wide at a median of $381 across 213 repairs, and the company median for a will-not-drain call overall is $377 across 508 jobs. Our local job came in below both, at $290, because the pump was sound and the fault was in its wiring.
Before the pump the technician also checks the drain hose and the filter, since a kink or a hose pushed too far into the standpipe produces the same symptom.
Have you ever replaced a control board on a washer here?
Not in 24 High Point jobs. Company-wide the motor control board is 163 of 4,763 washer repairs at a median of $436, so it is routine work rather than rare — this city simply has not produced one yet.
Everything on the local list is mechanical: a seal, a pump connection, a belt and pulley, a supply tap, a coupling. That is the main reason the local median of $304 sits $66 under our company figure.
Which washer brands do you service in High Point?
Every one of the 24 local work orders names a brand, which is unusual: Whirlpool eight, GE six, Maytag three, then Samsung, LG and Amana twice each and one Kenmore. We also service KitchenAid, Bosch, Electrolux, Frigidaire, Speed Queen and Haier here. Whirlpool and GE lead locally and they lead company-wide too.
Where it matters to you is parts: Whirlpool, GE and Maytag belts, pumps, couplings and suspension kits are commonly on the van or next-day.
My washer walks across the floor on spin. Do you fix that here?
Yes, and it is the leading repair in both of our other Triad cities even though High Point has not produced one yet. On a top-loader it is the suspension rods, on a front-loader the shock absorbers, at a company median of $367 across 195 repairs.
Tell us at booking whether the machine loads from the top or the front and whether it sits level on all four feet — an out-of-level cabinet both causes the symptom and wears the parts out early, and the technician levels it as part of the repair.
How long has Bozmanfix been working in High Point?
Since March 2026. All 72 High Point work orders on our books, including these 24 washer jobs, date from then, which is why this page prints six invoices with their sample size rather than a seasonal claim. Five months is not enough history to say which month washers fail in this city. The company medians quoted throughout come from more than 66,000 jobs across eight metro areas.
Other Appliance Repair in High Point
The rest of our High Point coverage, with the local job counts behind each page.
Appliance Repair in High Point — city hub, all six machines Serving High Point and the wider Charlotte area → View our full service areaBook Washer Repair in High Point
24 washer jobs on record since March 2026 in 24 separate households, at a median of $304 with a part fitted, and all six invoices published. Top-load, front-load and stacked. Every ZIP code covered, no travel charge inside the city, 90-day parts and labour warranty.