Oven and Range Repair in Winston-Salem, NC
Oven and range repair in Winston-Salem runs a median of $369 once a part is fitted, from six component repairs among 12 local jobs. Six is a small sample and we print all of it rather than rounding it into a range: $249, $265, $352, $386, $461 and $546.
What sets this city apart is the top of that list. Two of the six repairs were main control boards, at $461 and $546 — and company-wide the board is only about 5 percent of oven repairs.
That is the whole reason the local median sits so close to our company figure of $380 across 1,879 repairs, despite the cheapest local job being a $249 element rewire rather than a replacement.
Oven and Range Repair in Winston-Salem — Gas and Electric
Mobile service across every Winston-Salem ZIP code with no travel charge inside the city. The $99 diagnostic is applied to the repair once you approve it, $150 on a double wall oven because two cavities and two control circuits have to be assessed, and the price for the whole job is fixed before any work starts.
All Six Winston-Salem Invoices, With the Part Named
| What was replaced | Winston-Salem invoice | Company median | Company n |
|---|---|---|---|
| Bake element rewired, KitchenAid | $249 | $325 element replaced | 89 |
| Part not named on the work order | $265 | — | — |
| Bake igniter, GE | $352 | $352 | 221 |
| Maintenance and service, GE | $386 | — | — |
| Main control board | $461 | $475 | 89 |
| Main control board, Whirlpool | $546 | $475 | 89 |
| All Winston-Salem oven repairs with a part | $369 median, 6 jobs | $380 | 1,879 |
| Diagnostic visit | $99 | $99 | — |
Why Winston-Salem Oven Work Looks the Way It Does
Two control boards in six repairs AGAINST 5 PERCENT COMPANY-WIDE
Across 1,879 oven and range repairs, the main control board is about 5 percent of what we replace, at a median of $475 over 89 jobs. In this city it is a third of the local sample, at $461 and $546.
Six invoices cannot prove a pattern and we are not going to claim one, but it does change what we tell you before a visit: on an oven that has lost its display, ignores commands or runs the wrong element, the board is a genuine candidate rather than a long shot, and it is the one oven part expensive enough that we will talk about the age of the machine before ordering it.
The cheapest repair here rewired an element rather than replacing it $249 AGAINST $325
A KitchenAid bake element was rewired for $249 instead of replaced at the company median of $325. Elements fail two ways: the element itself burns through, which is usually visible as a break or a blister, or the connection behind the rear panel degrades and the element never gets full current.
The second one looks identical from the front and costs less to put right. It is a good illustration of why we assess before quoting — the same symptom had two prices and this household got the cheaper of them.
GE is a third of the local book 4 OF 10 BRANDED
Ten of the twelve work orders name a brand: GE four, then Whirlpool and KitchenAid on two each, one Samsung and one LG. Company-wide our oven and range work runs GE 23.6 percent and Whirlpool 21.8 across 2,250 jobs, so the local leader matches the company leader here.
Both of the local igniter and maintenance jobs were GE, and one of the two boards was Whirlpool. As on every page: this is a map of what is installed in Winston-Salem kitchens and who gets called to it, not a ranking of which brand lasts.
27104 turned every paid visit into a repair 3 OF 3
Three jobs in 27104, all three paid, all three ending with a component fitted — including both control boards. Elsewhere: 27106 three jobs, 27105 three, and one each in 27107, 27101 and 27127. The city-wide picture is that nine of the twelve oven jobs were paid visits and six of those nine ended with a part.
And the ceiling on what any of this can tell you is fixed: every Winston-Salem work order dates from March 2026, when the route opened.
Ovens have the most seasonal curve in our whole book — company-wide November runs 12.3 percent of the year against February at 6.2, because a holiday roast is when a half-broken oven finally gets noticed — and we cannot yet say whether this city follows it.
Two details are worth telling us at booking, because they decide what the technician brings: whether the oven is gas or electric, and whether the fault is heat or controls. A gas machine that will not light usually needs an igniter on the van; a dead display or unresponsive buttons points at the board, and boards are ordered rather than carried.
Match Your Symptom to the Likely Cause
- Display dead, buttons unresponsive, or the oven ignores what you set — the main control board, and in this city that is a third of the local repairs, at $461 and $546 against a company median of $475 across 89 jobs. It is also the repair where we will ask how old the machine is before ordering the part.
- Gas oven slow to heat, or will not light at all — the igniter, our most-replaced component company-wide at $352 across 221 repairs, and our one local job landed on exactly that figure. The igniter weakens before it dies, so weeks of taking longer to reach temperature is the warning stage.
- Electric oven will not heat, or heats unevenly — the bake or broil element at a company $325, or the wiring behind it. Our local job rewired the connection for $249 rather than replacing the element. A burned-out element usually shows a visible break, blister or bright spot.
- Runs hot or cold by 25 to 50 degrees — the temperature sensor at a company $357 or the thermostat at $420. Put an oven thermometer on the middle rack, set 350°F and give it 20 minutes to settle: a swing of 25 to 30 degrees either side of the set point is normal cycling on a domestic oven, not a fault.
- One surface burner will not light, the others do — that burner alone: a blocked port, which clears with cleaning, or its electrode or the spark module at a company $358 across 15 repairs. All burners dead at once is a supply or module problem upstream instead.
- Door will not close flush, heat escaping around it — hinge or latch at a company $345, gasket at $460. The gasket costs more than the hinge because the job is slow, not because the part is dear.
- You can smell gas — do not touch any switch, open a window if one is beside you, leave, and call your gas utility emergency line from outside. That is a safety call rather than a repair booking, and we will not put a technician into a property with a live gas smell.
Winston-Salem Oven and Range Work by ZIP Code
| ZIP | Area | Jobs | Paid visits | Part fitted |
|---|---|---|---|---|
| 27104 | West Winston-Salem | 3 | 3 | 3 |
| 27106 | Northwest Winston-Salem | 3 | 3 | 0 |
| 27105 | Northeast Winston-Salem | 3 | 0 | 0 |
| 27107 | Southeast Winston-Salem | 1 | 1 | 1 |
| 27101 | Downtown and central | 1 | 1 | 1 |
| 27127 | South Winston-Salem | 1 | 1 | 1 |
Winston-Salem is the county seat of Forsyth County and the second city of the Piedmont Triad. Six ZIP codes appear in our oven book and every Winston-Salem ZIP is covered at the same rate with no travel charge inside the city.
We service gas and electric, freestanding ranges, slide-ins, wall ovens and double wall ovens, and the work is done in the kitchen — there is no counter or depot to bring a range to.
Oven and Range Brands We Are Called To in Winston-Salem
| Brand | Winston-Salem oven jobs | Company share of oven and range work |
|---|---|---|
| GE | 4 | 23.6 percent |
| Whirlpool | 2 | 21.8 percent |
| KitchenAid | 2 | — |
| Samsung | 1 | 16.0 percent |
| LG | 1 | — |
| Frigidaire | none in the local book | 15.6 percent |
| Branded jobs | 10 of 12 | 2,250 company oven and range jobs |
We also service Frigidaire, Maytag, Bosch, Amana and Kenmore ovens and ranges here. Ten branded jobs is a list rather than a distribution and we will not present it as reliability. On lower-volume and premium models we check part availability before dispatch and give you the honest answer, because on some ranges that is a week rather than a day.
Repair or Replace, in Winston-Salem Numbers
Ovens usually sit at the favourable end of this arithmetic, because the parts that fail most are the cheap ones.
An igniter at $352, an element at $325 or a sensor at $357 against $700 to $1,400 for a mid-range freestanding replacement is not a close decision, and it stays uncontroversial at ten or twelve years, because an oven cavity does not wear out the way a compressor or a bearing does.
This city has produced the exception twice. A control board at $461 or $546 on a machine already past twelve years is a genuine decision, because the board is the one oven part whose failure often follows another and whose price approaches a meaningful share of a new range.
The counterweight is installation: on a built-in wall oven or a premium slide-in, replacing means cabinetry and fitting as well as the appliance, which pushes the arithmetic firmly back toward repair even at $546. We will put both figures in front of you at the assessment rather than after the range is apart.
Typical service lives are on how long ovens last, temperature complaints on oven temperature issues, and the break-even arithmetic in the repair versus replacement guide.
Discounts Applied Automatically
Priority Membership
$179 a year — five diagnostics, priority slots
- Five free diagnostic visits a year, a $495 value
- Priority scheduling with 24 to 48 hour response
- $30 off labor on every repair
- Extended warranty on all Bozmanfix work
What Customers Say About Our Oven and Range Work
“Nick fixed our oven fast and did a good job. I would recommend this company to anyone.”
“My oven was taking a long time to start. Scheduled next day. Mike came out, quickly diagnosed the issue, fixed my oven in an hour and a half. Would use again!”
“Nick was professional and very quick. He fixed our oven with ease. The part took longer to arrive than expected but we were patient. Would recommend to anyone.”
“8 inch Wolf oven experienced a bad fan. Once the new fan arrived, it was installed within minutes. Excellent service.”
Oven and Range Repair in Winston-Salem — Questions We Get
How much does oven repair cost in Winston-Salem?
The median is $369 once a part is fitted, from six component repairs among 12 local jobs. The six invoices were $249, $265, $352, $386, $461 and $546. By part, locally: bake element rewired $249, gas igniter $352, maintenance and service $386, main control board $461 and $546.
Each figure includes the part, the labour and the service call. Our company oven and range median is $380 across 1,879 repairs, with the middle half between $307 and $494. The diagnostic itself is $99, or $150 on a double wall oven.
Why were two of your six local repairs control boards?
Honestly, we do not know — six invoices cannot support an explanation and we are not going to invent one. What we can tell you is the contrast: company-wide the board is about 5 percent of oven repairs, at a median of $475 across 89 jobs, and in this city it is two of six.
Practically it means that if your oven has lost its display or stopped responding to the controls, the board is a real candidate here rather than a long shot, and we will ask the machine age before ordering the part.
Is a $500 control board worth fitting?
It depends on the machine and on how it is installed. On a freestanding range past twelve years, $546 against $700 to $1,400 for a replacement is a genuine decision and we will say so.
On a built-in wall oven or a premium slide-in it is usually still the better buy, because replacing means the appliance plus installation plus, often, cabinetry work to fit a unit that is rarely the same size as the one coming out.
We put the repair figure next to a realistic replacement figure at the assessment, before anything is taken apart.
My gas oven takes forever to heat. Is it the igniter?
Very likely. The igniter is the single most replaced component in our entire book — 221 replacements at a company median of $352 — and our one Winston-Salem job came in at exactly that figure. It does not fail suddenly: it weakens, draws less current, and eventually the gas valve stops opening because it never sees enough draw to trigger.
Weeks of the oven taking longer and longer to reach temperature is the warning, and it is far easier to schedule before it strands you mid-recipe.
Do you charge to adjust an oven that runs hot or cold?
No, and no such line exists on our invoices. If nothing needs replacing, the bill is the $99 diagnostic and nothing further. Before you book, put an oven thermometer on the middle rack, set 350°F and give it 20 minutes to settle — a swing of 25 to 30 degrees either side of the set point is normal cycling on a domestic oven.
If you are seeing 50 degrees or more, that is usually the temperature sensor at a company $357 or the thermostat at $420, which is a part rather than a setting.
Which oven brands do you service here?
The local book names GE four times, Whirlpool and KitchenAid twice each, and one Samsung and one LG, out of ten branded jobs in twelve. We also service Frigidaire, Maytag, Bosch, Amana and Kenmore in this city, gas and electric, freestanding, slide-in, wall and double wall.
GE leads locally and it leads company-wide at 23.6 percent of 2,250 oven jobs. Treat that as what is installed nearby rather than as a reliability ranking.
Do you charge more for a double wall oven?
The diagnostic is $150 rather than $99, because a double wall oven is two cavities with two heating circuits and often two control circuits, and both halves have to be assessed to establish which one has failed.
Everything after that is identical: the diagnostic is applied to the repair when you approve it, the 90-day parts and labour warranty applies, and the veteran, senior and new-customer discounts work the same way. Tell us at booking so the right length of visit is scheduled.
How long has Bozmanfix been working in Winston-Salem?
Since March 2026. All 146 Winston-Salem work orders on our books, including these 12 oven and range jobs, date from then, which is why this page prints six invoices rather than a seasonal trend — and ovens have the sharpest seasonal curve in our whole book, peaking in November company-wide.
Five months is not enough history to say whether this city follows it. The company medians quoted throughout come from more than 66,000 jobs across eight metro areas.
Other Appliance Repair in Winston-Salem
The rest of our Winston-Salem coverage, with the local job counts behind each page.
Appliance Repair in Winston-Salem — city hub, all six machines Serving Winston-Salem and the wider Charlotte area → View our full service areaBook Oven or Range Repair in Winston-Salem
Gas and electric, freestanding, slide-in and wall ovens, across every Winston-Salem ZIP code with no travel charge inside the city. Six local component repairs published in full and 1,879 across the company, so you get a real figure with its sample size attached. $99 diagnostic applied to the repair, $150 on a double wall oven, 90-day parts and labour warranty.