Dryer Repair in Northwest Jacksonville, FL
Not one of our eight paid dryer visits in Northwest Jacksonville ended with a component fitted and the machine drying again. We hold 13 dryer jobs across 32209, 32208 and 32220, 8 paid and 7 with a component replaced, at a local median of $366 — fourteen dollars above our company figure of $352 across 4,218 repairs, which is close enough to call agreement.
The practical reading is simple: a dryer that has stopped in this district is genuinely broken. A dryer is mechanically a heater, a motor, a belt and a fan, with far fewer soft complaints than a refrigerator or an oven, and that shows up in our book here more sharply than anywhere else.
Dryer Repair in Northwest Jacksonville, FL
No heat, damp clothes, will not tumble, shuts off part way, or squealing. Across 32209, 32208 and 32220 including the rural western end, with the $99 diagnostic coming off the bill when you approve the repair.
What Dryer Repair Costs, by Component
Seven local component jobs confirm a bottom line but cannot price ten separate parts, so the component rows below are company-wide.
Each figure is the part, the labor and the service call together — not the price of the component on a parts website, which is where most published repair prices go wrong by a factor of two or three. A drive belt is a cheap object and a $322 job.
| Repair | Median, full ticket | Source | Jobs (n) |
|---|---|---|---|
| Door switch | $321 | Company-wide | 54 |
| Drive belt | $322 | Company-wide | 259 |
| Thermal fuse | $332 | Company-wide | 84 |
| Drum rollers or idler | $349 | Company-wide | 218 |
| Thermostat | $350 | Company-wide | 144 |
| Blocked vent cleared | $350 | Company-wide | 43 |
| Heating element | $362 | Company-wide | 360 |
| Blower wheel | $368 | Company-wide | 22 |
| Drive motor | $394 | Company-wide | 55 |
| Control board | $478 | Company-wide | 71 |
| All dryer jobs with a part replaced | $352 · middle half $294 to $437 | Company-wide | 4,218 |
| All dryer jobs with a part replaced | $366 · middle half $350 to $405 | Northwest Jacksonville | 7 |
One Repair We Sold With No Warranty, in Writing
A 32208 ticket reads repair of the power button on the dryer, no warranty, at $195. That phrase was put there on purpose and it is worth explaining, because it is the same principle that runs through every page on this site.
Sometimes the correct part is not available, or the household would rather pay less for a repair to an existing component than replace an assembly. On a control panel, repairing a failed switch rather than fitting a new panel can save a great deal of money — and it also means the surrounding assembly is the same age it was before we arrived.
We will do that work when it is what the customer wants, we will charge less for it than the replacement, and we will write no warranty on the paperwork rather than imply a guarantee we cannot stand behind. For comparison, a full dryer control board is a $478 company median. Anyone offering a repair-in-place with a warranty attached is worth asking what exactly is covered.
Why Northwest Jacksonville Dryers Fail the Way They Do
One local untagged ticket is the best argument on this page for calling early: belt replacement, cleaning inside the dryer, cleaning and lubricating two rollers, at $315 — below our company drive belt figure of $322 for the belt alone, and it caught three things at once before any of them turned into an element or a motor.
The sequence in a neglected dryer runs the other way. The vent silts up, the machine runs longer and hotter to shift the same load, the safety cut-outs trip and eventually fail, and the heating element cooks. Company-wide, no heat is our largest dryer symptom category at 969 repairs, with damp clothes a further 226, and a meaningful share of both are airflow rather than electrical.
Eight paid visits, eight parts fitted 100 PERCENT
Every paid dryer visit in this district ended with a part fitted. Set that against the same district figures for ovens at 4 of 7 paid visits, washers at 9 of 21 and refrigerators at 8 of 21, and against our company dryer rate of 20.5 percent.
Dryers behave this way across our whole book and the reason is mechanical: there are simply fewer settings to get wrong and fewer soft failures than on a refrigerator or an oven. The one thing worth mentioning at booking is the vent, because a blocked duct is the cheapest fault on this page and the one that causes the expensive ones.
The cheapest genuine dryer repair here was $315, and it did three jobs BELT, CLEAN, TWO ROLLERS LUBRICATED
That one ticket is worth more than the median. The drive belt is our second most replaced dryer part company-wide at 259 replacements, and worn drum rollers left alone eventually take the belt with them — so replacing the belt while cleaning and lubricating the rollers is the version of this repair that lasts.
Company-wide, noise is 601 dryer repairs at a $349 median. If your dryer has started squealing or rumbling, that is the moment to call, not after it stops turning altogether.
A combination washer-dryer in the book, and what it costs to diagnose GE COMBO · $419.80
One local 32209 ticket is a GE washer-dryer combination unit where the customer reported that the unit was not draining and clothes remained wet — the two symptoms are linked on a combo, because the same cycle handles both.
It came to $419.80. Worth knowing before you book: on a stacked or combination laundry unit the diagnostic is $150 rather than $99, because the two halves have to be separated before anything can be inspected.
Like the standard fee it comes off the bill when you approve the repair, and we ask about the configuration at booking rather than at the door.
Twelve of thirteen jobs are from the last twelve months THE ONLY GROWING ROUTE IN THE CITY
This district is the only one in Jacksonville where our volume is still climbing — 22 jobs across all appliances in 2024, 49 in 2025 and 49 through August 2026 — and dryers track that almost completely, with twelve of thirteen inside the last year.
So the $366 figure was set by recent work at current parts prices rather than averaged against older invoices. It does not solve the sample size problem: seven component jobs is seven, which is why every component row on this page is company-wide and only the bottom line is local.
Stacked or combination unit? Say so at booking — $150 diagnostic, extra time scheduled, applied to the repair. Book online or call (954) 902-6229.
Match Your Symptom to the Likely Cause
- Tumbles but no heat at all — heating element at $362, thermal fuse at $332, or a thermostat at $350. Our largest dryer category company-wide, 969 repairs at a $368 median. One local ticket is a replacement heating element kit at $365.99. Check the vent first. See dryer not heating.
- Heats but clothes are still damp — nearly always airflow: a blocked vent, a crushed hose, or a failing blower wheel at $368. Company-wide 226 repairs at a $365 median.
- Squealing, grinding or rumbling — drum rollers and the idler pulley at $349. One local job replaced the belt while cleaning and lubricating two rollers at $315. This is the moment to call.
- Motor hums but the drum will not turn — drive belt at $322, our second most replaced dryer part with 259 replacements, or seized drum rollers.
- Starts then shuts off part way through — a cut-out opening because the machine is overheating, which points back at the duct rather than the electrics.
- Dead at the panel, or a button not responding — control board at $478, or sometimes a repair to the switch itself. One local ticket did exactly that at $195, sold with no warranty. See replacing a dryer heating element.
Where in Northwest Jacksonville We See This Work
Seven of our 13 dryer jobs are in 32209, five in 32208 and one in 32220. Twelve of the thirteen fall inside the last twelve months. Of the branded machines: Maytag 2, GE 2, Samsung 2, Whirlpool 1. Company-wide our dryer order runs Samsung 25.8 percent, Whirlpool 19.3 and GE 17.4, so the mix here is broadly ordinary on a small sample.
On the geography: 32220 covers 38.574 square miles of largely rural western Duval County, so addresses on this page can be a long way apart — there is no travel surcharge, but book early in the day if you are toward the western edge.
On the name: the Postal Service lists all three ZIPs as Jacksonville and nothing else, with Jax as a name to avoid; Northwest Jacksonville is the City of Jacksonville planning district name.
| ZIP | Dryer jobs | Water hardness | Land area |
|---|---|---|---|
| 32209 Jacksonville | 7 | 248 ppm · 14 grains · Very Hard | 9.308 sq mi |
| 32208 Jacksonville | 5 | 229 ppm · 13 grains · Very Hard | 11.527 sq mi |
| 32220 Jacksonville | 1 | 270 ppm · 16 grains · Very Hard | 38.574 sq mi |
| All three | 13 jobs, 8 paid, every paid visit fitted a part | JEA published table by ZIP | 59.409 sq mi |
Around Northwest Jacksonville
Dryer work in the neighbouring districts is on its own pages. South-east across the Trout River is Riverside, Avondale and Springfield, where half our paid dryer visits were on stacked units. North is Northside and Oceanway and south is Westside.
East over the bridges is Arlington, where one invoice was a vent clean at $240 with no part at all, and beyond it Atlantic Beach and Neptune Beach, where we have never had a job tagged as a dryer.
Down the river are San Marco and San Jose, where every paid dryer visit also fitted a part, and Mandarin. The Northwest set starts at the Northwest Jacksonville appliance repair hub.
Repair or Replace a Dryer Here
A single-part dryer repair runs $322 to $394 on the component table, against a mid-market replacement dryer at roughly $650 to $1,100 installed. On anything under about ten years old the repair is clearly ahead, and dryers reward repair longer than most appliances because there is simply less in them to fail.
The local book supports that: the $315 belt-and-rollers job and the $365.99 heating element kit are both a third of a new machine. The control board at $478 is the only single line that starts an argument, and even that is well under half.
Where it turns is a bundle on an old machine — an element, two or three thermostats, a roller and a clean together, past a decade of service — and we put the full total in front of you before touching anything.
One more thing worth saying: if a technician quotes you an element without mentioning the vent, ask why, because a new element in a blocked duct is on a short clock. Framework: repair or replace guide and how long dryers last.
Discounts Applied Automatically
Priority Membership
$179 a year — five diagnostics, priority slots
- Five free diagnostic visits a year, a $495 value
- Priority scheduling with 24 to 48 hour response
- $30 off labor on every repair
- Extended warranty on all Bozmanfix work
What Jacksonville Area Customers Say About Bozmanfix
“They were very quick and prompt with showing up to take care of our dryer on a Saturday afternoon. Thank you.”
“Dmitriy did efficient and effective work for my dryer that had a busted component. Showed me the breaks specifically and explained the repairs well. Happy and would use again.”
“Was having dryer problems. Chris was great. Very efficient, was in and out in 15 minutes, super easy. Highly recommend.”
“Easy to schedule, next day service, scheduled on a Sunday. Prompt and on time, communicated issues well and quickly diagnosed and resolved the problem. Highly recommend. Will use them again.”
Dryer Repair in Northwest Jacksonville — Questions We Get
How much does dryer repair cost in Northwest Jacksonville?
Our local median is $366 once a part is replaced, from seven invoices, with a middle half of $350 to $405. That is $14 above our company median of $352 across 4,218 repairs, which is close enough to call agreement.
By component budget roughly $321 for a door switch, $322 for a drive belt, $332 for a thermal fuse, $349 for drum rollers, $350 for a thermostat or a vent clearance, $362 for a heating element and $478 for a control board.
One local ticket is a replacement heating element kit at $365.99, sitting almost exactly on the company element figure.
Is it true that every dryer visit you make here finds a broken part?
In this district, so far, yes — eight paid visits and eight parts fitted. We are not claiming it will hold forever on a sample of eight.
The mechanical reason is real though: a dryer is a heater, a motor, a belt and a fan, with far fewer settings to get wrong and far fewer soft complaints than a refrigerator or an oven, where a clean or a setting is often the answer.
My dryer runs but the clothes are still damp. What is wrong?
That symptom points at airflow far more often than at the heater. Go outside, run the dryer and watch the exterior vent flap: if it does not open or you cannot feel air pushing out, the duct is blocked and you have found it. Then check the flexible hose behind the machine for crushing or packed lint.
Our company median for clearing a blocked vent is $350 across 43 jobs, and it is the cheapest thing on this page that fully solves a no-heat or damp-clothes complaint. If the airflow is fine, the next candidates are the blower wheel at $368 or a partly failed element.
Why did one of your repairs come with no warranty?
Because it was a repair to an existing component rather than a replacement. One local 32208 ticket reads repair of the power button on the dryer, no warranty, at $195. Sometimes the correct part is not available, or a household would rather pay less to repair a failed switch than fit a whole new control panel — which on a dryer is a $478 company median.
We will do that work when it is what the customer wants and charge less for it, but the surrounding assembly is the same age it was before we arrived, so we write no warranty on the paperwork rather than imply a guarantee we cannot stand behind.
My dryer is squealing. Can it wait?
It can, but it gets more expensive. Squealing and rumbling is normally the drum rollers and idler pulley, at a company median of $349 across 218 replacements, and company-wide noise accounts for 601 dryer repairs. Left alone, worn rollers eventually take the drive belt with them, and then you are paying for both.
One local job caught it at the right moment — belt replacement with cleaning and lubricating two rollers at $315, which is below our company figure for the belt alone. That is the argument for calling when it starts making a noise rather than when it stops turning.
Why is the diagnostic $150 on a stacked or combination unit?
Because the two halves share one cabinet and have to be separated before anything can be inspected, which is substantially longer than opening the back of a freestanding machine. One of our local jobs is a GE washer-dryer combination where the customer reported the unit was not draining and clothes remained wet — on a combo those two symptoms are linked, because the same cycle handles both.
That job came to $419.80. Like the standard $99, the $150 comes off the bill when you approve the repair, so tell us the configuration at booking.
Do you price gas dryer repairs?
We repair them, but we will not publish medians for the gas-specific parts. Company-wide we hold fewer than ten igniter replacements and fewer than ten valve coil replacements, and a median from a sample that small is a number pretending to be information. For those components we quote at the diagnostic from the actual part price.
Everything else on a gas dryer behaves exactly as the table on this page describes — belt, rollers, blower, thermostats, control board, vent — because those parts are shared with electric machines.
Other Appliance Repairs in Northwest Jacksonville, FL
Each page is built on its own local invoices and says where the sample runs out.
Appliance Repair in Northwest Jacksonville — the full district picture Serving Northwest Jacksonville, FL and the wider Jacksonville area → View our full service areaBook Dryer Repair in Northwest Jacksonville, FL
Thirteen dryer jobs on record across 32209, 32208 and 32220, and every paid visit found a genuine broken part. $99 diagnostic applied to the repair, 90-day parts and labor warranty.