Dryer Repair in San Marco and San Jose, Jacksonville FL

🌡️ 15 San Marco and San Jose Dryer Jobs ✅ All 12 Paid Visits Replaced Something 🧺 5 of Those 12 Were Stacked or Combination Units ⚠️ Stacked Diagnostic Is $150, Not $99 🛡️ 90-Day Parts and Labor Warranty

Every single paid dryer visit we have made in San Marco and San Jose replaced a part — twelve out of twelve. That is the only clean sweep of its kind anywhere in our Jacksonville book, against a company dryer part-fitted share of 79.5 percent and an all-appliance rate of 37 percent.

It sits inside a district where washers confirm the machine is sound 62.5 percent of the time, which makes the contrast sharper still. The second thing to know when you book is structural: five of those twelve visits were on a stacked or combination laundry unit, and the four largest dryer invoices we hold here were all stacked or combo machines.

On a stacked washer-dryer the diagnostic is $150 rather than $99, because the two halves have to be separated before anything can be seen. We hold 15 dryer jobs across ZIP codes 32207 and 32217, 12 paid and 11 with a component fitted.

Dryer Repair in San Marco and San Jose, FL 32207 and 32217

No heat, damp clothes, will not tumble, shuts off part way, or squealing. Stacked and combination units welcome, and the diagnostic comes off the bill when you approve the repair.

The Stacked Laundry Closet, and What It Does to the Bill

San Marco proper is a 1920s streetcar-era neighbourhood with a designated historic core, San Jose in 32217 is largely 1950s and 1960s, and the riverfront on both sides carries mid-rise condominiums. Older and denser housing means laundry in a closet rather than a laundry room, and a closet means a stacked or combination machine. Our invoices show it plainly.

TicketMachineWhat the paperwork records
$595.00Frigidaire washer-dryerCombination unit
$565.55GE stacked washer-dryerReplacing the control board
$550.90LG stacked washer-dryerLogged as a stackable combination
$539.25Stackable washer-dryerLogged as a stackable combination
$474.00Whirlpool dryerFreestanding
$396.75Samsung dryerFreestanding
$345.99Samsung dryerHeating element
$200.00LGLogged as a stackable combination
$397Median with a part replacedLocal, 11 jobs — lifted by the stacked units above
$352Median with a part replaced, middle half $294 to $437Company-wide, 4,218 repairs
💡 The local median of $397 is $45 above the company figure, and the four invoices above $500 are the whole of the difference. A stacked unit is not a more expensive repair, it is a longer one — the parts are the same, the access is not. That is precisely what the $150 diagnostic covers, and it is why we ask about your laundry configuration when you book rather than discovering it at the door.

What Dryer Repair Costs, by Component

Company-wide rows, because eleven local jobs cannot price ten components. Each figure is the part, the labor and the service call together — not the price of the component on a parts website, which is where most published repair prices go wrong by a factor of two or three.

RepairMedian, full ticketSourceJobs (n)
Door switch$321Company-wide54
Drive belt$322Company-wide259
Thermal fuse$332Company-wide84
Drum rollers or idler$349Company-wide218
Thermostat$350Company-wide144
Blocked vent cleared$350Company-wide43
Heating element$362Company-wide360
Blower wheel$368Company-wide22
Drive motor$394Company-wide55
Control board$478Company-wide71
All dryer jobs with a part replaced$352 · middle half $294 to $437Company-wide4,218
All dryer jobs with a part replaced$397 · five of twelve visits were stacked unitsSan Marco and San Jose11
💡 Gas igniters and valve coils are deliberately absent from this table. Company-wide we hold fewer than ten replacements of each, and a median from a sample that small is a number pretending to be information. On a gas dryer we quote those parts at the diagnostic from the actual price. Everything else on the table applies identically, because those components are shared with electric machines.

Why San Marco Dryers Fail the Way They Do

Two of our local invoices explain more than any median can. One reads dryer replacement of three thermostats and cleaning ventilation, at $649. Another reads dryer heating element replacement, cleaning inside, and roller repair, at $710 — that one was filed under the washer tag by mistake, and we corrected it before writing this page.

Both are the same story told twice: the machine was running hot enough to take out its safety cut-outs, and the cause was airflow. In an older house with a laundry closet the vent run is often longer, tighter and harder to get at than in a modern laundry room, which is exactly the condition that silts a duct up.

Twelve paid visits, twelve parts fitted, no exceptions

Every paid dryer visit in this district ended with a part fitted. Set that beside the same district figures for ovens at 9.1 percent, refrigerators at 47.4 and washers at 62.5, and against our company dryer rate of 20.5 percent, and the dryer stands alone.

Two things explain it. Mechanically a dryer is a heater, a motor, a belt and a fan, with far fewer settings to get wrong and far fewer soft complaints than a refrigerator or an oven. And on a stacked unit nobody calls a technician casually, because opening one is not something a household does to have a look. If your dryer here has stopped, expect it to be genuinely broken.

Thermostats replaced in twos and threes, always with a clean THREE ON ONE MACHINE

One local ticket replaced three thermostats on a single dryer and cleaned the ventilation. Another replaced a heating element together with a roller repair and an internal clean. Those thermostats are not failing independently — they are cut-outs, and they open because the machine is running hotter than it should.

Replacing an element without dealing with why it cooked puts the new part straight back on the same clock. The practical question to ask any dryer technician, ours included, is what they did about the airflow, not only what they fitted. Our company median for clearing a blocked vent is $350 across 43 jobs, and it is the cheapest thing on the table that fully solves a no-heat complaint.

Thirteen of fifteen jobs sit in 32207 THE SAN MARCO SIDE CARRIES THIS BOOK

Thirteen of our fifteen local dryer jobs are in 32207 and two in 32217, which is a heavier concentration than the district split overall, where 32207 holds 125 of 192 jobs. That tracks the housing: 32207 is the older, denser side with the historic core and the riverfront condominiums, and it is where the stacked laundry closets are.

It is also worth noting that thirteen of the fifteen fall inside the last twelve months, making dryers the freshest sample in the district apart from washers. These are current prices set by recent work.

One ticket says the dryer was fine, and we charged the diagnostic MACHINE RUNS PROPERLY

An untagged local invoice at $78 records in full: dryer inspected, no issues detected, machine runs properly. That visit is not in the twelve paid dryer jobs above because it was never tagged as a dryer, which is a fair illustration of why we treat every per-appliance count on this site as a floor.

It is also worth publishing on its own account. Sometimes the honest finding is that nothing is wrong, and the outcome is a diagnostic fee and a written note rather than a part nobody needed. We would rather record that than manufacture a repair.

Two checks the technician runs first a dryer here, and the first one is the important one. Go outside, start the dryer, and watch the exterior vent flap. If it does not open, or barely moves, or you cannot feel warm air pushing out, your problem is airflow rather than electrics — and that is the cheapest thing on this page to put right. Second, pull the flexible hose off the back of the machine and check both the hose and the wall duct for lint packed solid; a foil concertina hose crushed behind a machine in a tight closet is the classic version of this in San Marco, because there is less room behind the unit than in a purpose-built laundry room. That check also protects the heating element you might otherwise be paying $362 for.

Stacked or combination unit? Say so at booking — $150 diagnostic, extra time scheduled, applied to the repair. Book online or call (954) 902-6229.

Match Your Symptom to the Likely Cause

  • Tumbles but no heat at all — heating element at $362, thermal fuse at $332, or a thermostat at $350. Our largest dryer category company-wide, 969 repairs at a $368 median. Check the vent before assuming the element. See dryer not heating.
  • Heats but clothes are still damp — nearly always airflow: a blocked vent, a crushed hose, or a failing blower wheel at $368. Company-wide 226 repairs at a $365 median. In a laundry closet the hose is the usual culprit.
  • Starts then shuts off part way through — a cut-out opening because the machine is overheating, which points back at the duct. One local ticket replaced three thermostats and cleaned the ventilation at $649.
  • Motor hums but the drum will not turn — drive belt at $322, our second most replaced dryer part with 259 replacements, or seized drum rollers at $349. One local untagged invoice replaced an idler pulley and belt, another an idler pulley, belt and bearing kit at $402.48.
  • Squealing, grinding or rumbling — drum rollers and the idler pulley. Company-wide, noise is 601 dryer repairs at a $349 median. Left alone, worn rollers eventually take the belt with them.
  • Stacked unit dead at the panel — control board at $478. One local GE stacked unit needed exactly that, at $565.55 including the additional access. See replacing a dryer heating element.

Where in San Marco and San Jose We See This Work

Thirteen of our fifteen dryer jobs are in 32207 and two in 32217. Of the eight where our paperwork records a brand: Whirlpool 4, LG 2, Maytag 2, GE 1, Samsung 1, Frigidaire 1. Company-wide our dryer order runs Samsung 25.8 percent, Whirlpool 19.3 and GE 17.4, so this district is Whirlpool-heavy and light on Samsung — a housing-stock signal rather than a reliability one.

On the name: the Postal Service lists both ZIPs as Jacksonville only, with Jax as a name to avoid. San Marco and San Jose are neighbourhood names, not postal cities. One caution on volume: 95 of our 192 local tickets never record which appliance was involved, so fifteen is a floor rather than a total, and one $710 dryer job was filed under the washer tag until we corrected it.

ZIPDryer jobsWater hardnessHousing units
32207 Jacksonville13298 ppm · 17 grains · Very Hard19,402
32217 Jacksonville2285 ppm · 17 grains · Very Hard8,787
Both15 jobs, 12 paid, 11 with a partJEA published table by ZIP28,189

Around San Marco and San Jose

Dryer work in the neighbouring districts is on its own pages. South is Mandarin and beyond it St. Johns and Fruit Cove. East is Southside and the University of North Florida area in 32224. North over the bridges are Riverside, Avondale and Springfield, which also carries stacked laundry work, and Northwest Jacksonville, where every paid dryer visit has ended with a part fitted too.

North-east is Arlington, where one invoice was a vent clean with no part at all, and beyond it Atlantic Beach and Neptune Beach. Also Westside. The San Marco set starts at the San Marco appliance repair hub.

Repair or Replace a San Marco Dryer

A single-part dryer repair runs $322 to $394 on the component table, against a mid-market replacement dryer at roughly $650 to $1,100 installed. On anything under about ten years old the repair is clearly ahead, and dryers reward repair longer than most appliances because there is simply less in them to fail.

In this district one factor pushes the calculation further toward repair than the sticker price suggests: if your machine is stacked or a combination unit, replacing it means finding a machine that fits the same closet opening with the same plumbing and vent arrangement, which is a much narrower shopping problem than buying a freestanding dryer.

At $550 to $595 those local stacked invoices still beat that outcome comfortably. Where it does turn is a bundle on an old machine — an element, two or three thermostats, a roller and a clean together, past a decade of service. We put the full total in front of you before touching anything. Framework: repair or replace guide and how long dryers last.

Discounts Applied Automatically

$30 OFFVeteransEvery repair
$30 OFFSeniorsEvery repair
$20 OFFNew CustomersFirst repair

Priority Membership

$179 a year — five diagnostics, priority slots

  • Five free diagnostic visits a year, a $495 value
  • Priority scheduling with 24 to 48 hour response
  • $30 off labor on every repair
  • Extended warranty on all Bozmanfix work

What Jacksonville Area Customers Say About Bozmanfix

★★★★★

“Dmitriy did efficient and effective work for my dryer that had a busted component. Showed me the breaks specifically and explained the repairs well. Happy and would use again.”

— Nathaniel Wiest · Verified Google review
★★★★★

“Was having dryer problems. Chris was great. Very efficient, was in and out in 15 minutes, super easy. Highly recommend.”

— Wilhelmina Krekel · Verified Google review
★★★★★

“Vladimir was very quick and efficient. Very kind and respectful to our home.”

— Rolande Paul · Verified Google review
★★★★★

“Found a way to fix it. Impressed, as it was not easy.”

— Richard Wheeler · Local Guide

Dryer Repair in San Marco — Questions We Get

How much does dryer repair cost in San Marco, Jacksonville?

If one component has failed, budget from the company figures: $322 for a drive belt, $332 for a thermal fuse, $349 for drum rollers, $350 for a thermostat, $362 for a heating element, $478 for a control board — each parts, labor and the service call together.

Our local median with a part replaced is $397, which is $45 above the company figure of $352, and the whole of that difference is the four stacked and combination units in our sample that ran $539 to $595. If your laundry is a stacked unit, budget nearer the local figure and remember the diagnostic is $150 rather than $99.

Why is the diagnostic $150 on a stacked washer-dryer?

Because the two halves share one cabinet and have to be separated before anything can be inspected, which is substantially longer than opening the back of a freestanding machine.

It matters more in this district than anywhere else we work: five of our twelve paid dryer visits here were on stacked or combination units, and the four largest dryer invoices we hold in 32207 and 32217 were all stacked or combo machines.

The same $150 applies to a double wall oven for the same reason. Like the standard $99 it comes off the bill when you approve the repair, and we ask about your laundry configuration at booking rather than at the door.

Is it true that every dryer visit you make here finds a broken part?

In this district, so far, yes — twelve paid visits. That is the only clean sweep of its kind in our Jacksonville book, against a company dryer part-fitted share of 79.5 percent. We are not claiming it will hold forever on a sample of twelve.

Two things do explain it. A dryer is mechanically simple, so it produces far fewer soft complaints than a refrigerator or an oven, where a setting or a clean is often the answer. And nobody calls a technician casually about a stacked unit, because opening one is not something a household does to have a look.

My dryer runs but the clothes are still damp. What is wrong?

That symptom points at airflow far more often than at the heater. Go outside, run the dryer and watch the exterior vent flap: if it does not open or you cannot feel air pushing out, the duct is blocked and you have found it.

Then check the flexible hose behind the machine for crushing or packed lint — in a laundry closet there is less room behind the unit than in a purpose-built laundry room, so a crushed hose is the common version here.

Our company median for clearing a blocked vent is $350 across 43 jobs. If the airflow is fine, the next candidates are the blower wheel at $368 or a partly failed element.

Why did my repair include three thermostats?

Because thermostats in a dryer are safety cut-outs, and they open when the machine runs hotter than it should. One local invoice records exactly that: three thermostats replaced on a single dryer together with cleaning the ventilation, at $649. A second replaced a heating element with a roller repair and an internal clean at $710.

The sequence is nearly always the same — the vent silts up, the dryer runs longer and hotter, the cut-outs trip and then fail, and eventually the element cooks. Fitting a new element and leaving the duct blocked simply restarts the clock, which is why both of those tickets also carry a clean.

Do you price gas dryer repairs?

We repair them, but we will not publish medians for the gas-specific parts. Company-wide we hold fewer than ten igniter replacements and fewer than ten valve coil replacements, and a median from a sample that small is a number pretending to be information. For those components we quote at the diagnostic from the actual part price.

Everything else on a gas dryer behaves exactly as the table on this page describes — belt, rollers, blower, thermostats, control board, vent — because those parts are shared with electric machines.

Is my dryer worth repairing?

Usually, and for longer than most appliances. A single-part repair here runs $322 to $394 against $650 to $1,100 for a mid-market replacement installed.

If your machine is stacked or a combination unit the case for repair is stronger still, because replacing it means finding a unit that fits the same closet opening with the same plumbing and vent arrangement — a much narrower shopping problem than buying a freestanding dryer.

The case that turns is a bundle on an old machine: an element, two or three thermostats, a roller and a clean together, past a decade of service. We give you the full total before starting rather than after.


Book Dryer Repair in San Marco and San Jose, FL

Fifteen dryer jobs on record in 32207 and 32217, and twelve of twelve paid visits replaced a part. Stacked and combination units welcome, diagnostic applied to the repair, 90-day parts and labor warranty.

Book online Call us
Book online Call us