Washer Repair Loganville GA
Washer repair in Loganville, GA runs a median of $398 once a part is actually replaced, which is the highest washer median of the six cities in this cluster, and there is a specific reason for it rather than a local rate. It comes from 57 washer jobs inside Loganville across 56 separate households, 45 of them finishing as paid work and 26 with a part fitted, with the middle half between $315 and $547 and a ceiling of $751.
Two of our six written-up local repairs are control board replacements, at $751 and $547, and a motor control board is $436 all in on our company-wide table against $341 for a drive belt. A file weighted toward boards produces a higher median with every household paying the same price for the same part.
Washer Repair in Loganville, GA
Will not drain, will not spin, lights up and refuses to run, agitates but will not spin, water on the laundry room floor, hammering on the spin cycle. Top-load and front-load. Total confirmed before the work starts.
The Washer Repairs We Have Actually Done in Loganville
Twenty-six local part-repairs, six of them written up in enough detail to name the work. This is the most varied written-up washer file in the cluster: two boards, a transmission, a pump, a valve and a sensor, which between them cover almost every system in the machine.
| Date | Total | What the invoice records |
|---|---|---|
| May 2026 | $751 | Samsung, control board replaced |
| May 2026 | $547 | GE, control board replaced |
| January 2026 | $460 | Frigidaire, transmission assembly replaced |
| March 2026 | $402 | Kenmore, drain pump replaced |
| March 2026 | $395 | Samsung, water valve replaced |
| September 2025 | $377 | LG, position sensor assembly replaced |
What a Washer Repair Costs, by the Part That Failed
The table is company-wide, from 4,763 completed washer jobs, because 26 local repairs cannot honestly price eight separate components. Every figure is the full ticket: the part, the labor and the service call added together. The Loganville local median of $398 sits between the drive motor line and the motor control board line, high on this table and, as the lead explains, for a reason.
| What failed | Median total | Middle half | Jobs (n) |
|---|---|---|---|
| Drive belt | $341 | $310 to $445 band | 74 |
| Door lock or lid switch | $351 | $310 to $445 band | 143 |
| Water inlet valve | $362 | $310 to $445 band | 137 |
| Shock absorbers or suspension rods | $367 | $310 to $445 band | 195 |
| Drain pump | $381 | $310 to $445 band | 213 |
| Drive motor | $387 | $310 to $445 band | 81 |
| Motor control board | $436 | $310 to $445 band | 163 |
| Front-load door boot seal | $450 | $310 to $445 band | 49 |
The distance from the cheapest line to the most expensive is $109, which is the whole dynamic range of ordinary washer repair.
Two of our local jobs sit above every line on that table, at $547 and $751, and that is scope rather than pricing: a board replacement that runs high is usually one where the wiring harness, the user interface board or a failed component that took the board out also had to be dealt with.
It is worth knowing that a board is the fault most often guessed at and least often correct on its own, which is why the technician tests the lock circuit, the motor and the sensors before condemning anything expensive.
Why Loganville Washers Fail the Way They Do
A transmission assembly at $460, which almost nobody will quote RARE REPAIR
One Frigidaire ticket in our Loganville file is a transmission assembly replacement at $460, and it is worth explaining because most repair companies will not touch it. On an older belt-and-transmission top-loader, a gearbox under the tub converts motor rotation into the back-and-forth of agitation and then locks up for the spin.
When it fails you get a machine that fills and drains perfectly, hums, and does neither job properly, or agitates and will not spin. It is a heavy component and a long job, which is why the default advice elsewhere is to buy a new machine.
At $460 against a replacement washer delivered and installed for around $700 before haul-away, it is not a close call on a machine that is otherwise sound.
A position sensor at $377 is the direct-drive equivalent LG HALL SENSOR
One LG ticket is a position sensor assembly replacement at $377. On a direct-drive washer there is no belt and no transmission: the motor drives the tub directly, and a Hall-effect sensor tells the control board exactly where the rotor is so the board can commutate the motor correctly.
When that sensor fails the machine cannot control the motor, so it will not spin, spins erratically, or throws a motor fault code, and the household reads it as a dead motor or a dead board. Both of those are more expensive than the sensor. It is one of the clearest examples on this site of why testing beats guessing.
Two control boards, and why they lift the median $751 AND $547
A Samsung board at $751 and a GE board at $547, against a company-wide motor control board figure of $436. Those two invoices are the reason Loganville has the highest washer median in this cluster.
A board job runs above the table when the harness, the user interface board or the component that killed the board also needs replacing, and a board is not always the whole story: a shorted drain pump or a failed motor can take a board out, and fitting a new board without finding what killed the old one is how a machine comes back.
That is why the diagnostic tests the circuit rather than the symptom.
Will not drain and will not spin are the same complaint $351 OR $381
A washer that fills and then stops with water in the drum is the most common laundry call we take. The drain pump at $381 is the obvious suspect and was the right one on our Kenmore ticket at $402.
But a door lock or lid switch at $351 produces an identical complaint for a completely different reason: the machine will not drain or spin because it does not believe the door is safely shut, so it is refusing rather than failing.
A motor control board can do the same. The symptom cannot separate them and neither can a phone call, which is exactly what the diagnostic visit is for. See washer will not drain.
Samsung leads the laundry room here 10 OF 57
On our Loganville washer list Samsung is first at 10 jobs, then Whirlpool and GE at 7 each, Maytag at 6, and Kenmore, Insignia and Amana at 2 each with Frigidaire at 1. Whirlpool and Maytag are the same manufacturer under two badges, so that family is 13 of the 37 branded washers here against Samsung at 10.
The two families fail differently: the Whirlpool-family top-loaders bring shifter, lid-lock and transmission faults, and the Samsung and LG machines bring boards, position sensors and door boot seals, which is exactly the split our written-up tickets show. It is a count of service calls and not a reliability ranking, since a common brand generates more calls at the same failure rate.
No single hardness figure exists for this tap, and here that is literal THREE SUPPLIERS
Front-load owners are routinely told that hard water and detergent build-up cause smells and poor rinsing. We cannot support the first half of that in Loganville, and in this city the reason is unusually concrete.
The City of Loganville distributes water but produces none of it: it buys from the City of Monroe, which draws on the John T. Briscoe Reservoir and the Alcovy River, from Walton County, which uses the Lake Varner and Bear Creek reservoirs, and from Gwinnett County on Lake Lanier for emergency use.
At least four reservoirs and two rivers sit behind one tap, and the blend reaching a street can change with the supplier feeding the system. What genuinely produces a front-loader smell is the boot fold and the detergent drawer: items trapped in the seal, a machine never left open to dry, and too much detergent leaving residue.
🚚 23 of our 57 Loganville washer jobs landed in the last twelve months, and the whole city is one dispatch zone across both counties. Most washer repairs are a single visit, because the parts in the table above ride on the van.
Match Your Symptom to the Likely Cause
- Fills, then stops with water in the drum — drain pump at $381, which we replaced on a Kenmore locally at $402, a blocked pump filter or drain hose, or a door lock at $351 refusing to let the cycle continue. See washer will not drain.
- Lights up, beeps, and refuses to run a cycle at all — the door lock circuit or the control board. We replaced washer boards locally at $751 and $547, but the lock at $351 is the cheaper and commoner answer, so it is tested first.
- Agitates but will not spin on an older top-loader — the transmission assembly, which we replaced on a Frigidaire locally at $460. Most companies will not quote this repair and will tell you to buy a new machine.
- Will not spin, spins erratically, or throws a motor fault — on a direct-drive machine the position sensor, which we replaced on an LG locally at $377. Cheaper than the motor or the board that people usually assume.
- Fills slowly, or fills on one temperature only — the water inlet valve, which we replaced on a Samsung locally at $395.
- Hammers, walks or shakes hard on the spin cycle — shock absorbers or suspension rods at $367. Do not live with it; the tub bearing pays for it eventually. Washing machine out of balance explains why.
- Front-loader smells even after running empty — the boot seal fold and the detergent drawer. No single hardness figure exists for this tap, so we do not blame minerals.
Repair or Replace a Washer in Loganville
Every washer repair in our Loganville file finished at $751 or below, the median with a part is $398, and a mid-market replacement washer delivered and installed starts around $700 before haul-away and before the risk of a first-year fault on a new machine.
For the drain pump, the door lock, the valve, the belt, the motor, the position sensor, the suspension and even the transmission, repair wins on any machine not already past about twelve years.
The transmission case is worth repeating, because the standard advice elsewhere is to replace the machine and our own local invoice for that repair is $460.
The board is where the conversation gets closer, and this is the city where it comes up most. A washer control board at $547 or $751 on a machine already past fifteen years is approaching the cost of a new one, and the rest of the machine is the same age as the board.
We will say that in your laundry room rather than sell you the repair. The other genuine replacement case is a failed tub bearing, which is almost always the end point of a machine left hammering on tired suspension for a year, and catching the suspension at $367 is what prevents it.
Expected service life is in how long washing machines last and the framework in the repair or replace guide. The machine beside it is on the Loganville dryer page.
Discounts Applied Automatically
Priority Membership
$179 a year, five diagnostics and priority slots
- Five free diagnostic visits a year, a $495 value
- Priority scheduling with 24 to 48 hour response
- $30 off labor on every repair
- Extended warranty on all Bozmanfix work
What Atlanta Area Customers Say About Bozmanfix
“Had our washer fixed by Sergey and had an incredible experience. Great customer service and professionalism. We will call in the future for our other appliances!”
“Nick was great and able to come the same day I called to fix my washing machine. He had the part I needed and fixed the issue with no problem.”
“Sam was great! He got my washer working in no time!”
“Denis saved the day with my Maytag washer! The drum was shaking uncontrollably during the spin cycle.”
Loganville Washer Repair, Answered
How much does washer repair cost in Loganville, GA?
The median is $398 once a part is replaced, with the middle half of local jobs between $315 and $547 and a ceiling of $751, from 57 washer jobs inside Loganville.
That is the highest washer median of the six cities in this cluster, and the reason is composition rather than pricing: two of our six written-up local repairs are control boards. The $99 diagnostic comes off the bill when you approve the repair.
Why is washer repair more expensive in Loganville than nearby?
It is not. Every household pays the same price for the same part. A motor control board is $436 all in on our company-wide table against $341 for a drive belt, and two of our written-up local repairs are boards, at $751 and $547.
A local file weighted toward the expensive end of the table produces a higher median without anybody being charged differently. Price your own repair against the component table on this page rather than against the median.
My old top-loader agitates but will not spin. Is it worth fixing?
Usually yes, and this is the repair most companies will not quote. On a belt-and-transmission top-loader, a gearbox under the tub converts motor rotation into agitation and then locks for the spin, and when it fails you get exactly that symptom. It is a heavy component and a long job, which is why the default advice elsewhere is to buy a new machine.
We replaced a Frigidaire transmission assembly in Loganville at $460, against a replacement washer that starts around $700 delivered and installed.
My washer will not spin and shows a motor fault. Is the motor dead?
Often not. On a direct-drive machine there is no belt and no transmission: the motor drives the tub directly and a position sensor tells the control board where the rotor is so it can drive the motor correctly. When that sensor fails, the machine cannot control the motor and reports a motor or board fault.
We replaced an LG position sensor assembly in Loganville at $377, which is considerably cheaper than either of the parts people assume.
My washer will not drain. What is it likely to be?
Most often the drain pump at $381 all in, which we replaced on a Kenmore here at $402, or a blockage in the pump filter or drain hose. But a failed door lock or lid switch at $351 produces exactly the same complaint for a different reason: the machine refuses to drain or spin because it does not believe the door is safely shut.
A control board can do the same. The symptom cannot separate them and neither can a phone call.
Which washer brands do you see most in Loganville?
Samsung leads at 10 of 57 jobs, then Whirlpool and GE at 7 each, Maytag at 6, and Kenmore, Insignia and Amana at 2 each with Frigidaire at 1. Whirlpool and Maytag are the same manufacturer under two badges, so that family is 13 of the 37 branded washers here.
The two families fail differently, which is why we ask for the model number when you book. These are counts of service calls, not a reliability ranking.
Is hard water causing my front-loader to smell?
We cannot tell you that, and in this city the reason is unusually concrete. The City of Loganville distributes water but produces none of it: it buys from the City of Monroe, from Walton County and from Gwinnett County, drawing between them on at least four reservoirs and two rivers, so the blend reaching your street can change with the supplier feeding the system.
A front-loader smell is the boot fold and the detergent drawer: items trapped in the seal, a machine never left open to dry, and too much detergent leaving residue.
More Appliance Repair in Loganville, GA
The other appliances in the house have their own Loganville pages, each with its own local job count and its own component table.
Appliance Repair in Loganville Serving Loganville, GA and the wider Atlanta area → View our full service areaBook a Loganville Washer Technician
Locks, motors and sensors tested before boards are condemned, the $99 diagnostic applied to the repair, a firm total before the work starts and a 90-day parts and labor warranty.