Dishwasher Repair Loganville GA
Dishwasher repair in Loganville, GA runs a median of $429 once a part is actually replaced, which is the highest dishwasher median of the six cities in this cluster, where the others run $345 to $367. That is not a Loganville rate and this page is going to explain it rather than pocket it.
The figure comes from 39 dishwasher jobs inside Loganville across 36 households, 31 of them finishing as paid work and 13 with a part fitted, the deepest dishwasher file we hold for any city here. Three of our written-up local repairs are control board replacements, at $429, $454 and $457, and a dishwasher board is $387 all in on our company-wide table against $350 for a drain pump.
A file weighted toward boards produces a higher median with every household paying the same price for the same part.
Dishwasher Repair in Loganville, GA
Dead panel or a cycle that will not start, standing water in the bottom, dishes coming out gritty or greasy, a puddle at the toe kick. Both counties. Total confirmed before the work starts.
The Dishwasher Repairs We Have Actually Done in Loganville
Thirteen local part-repairs, five of them written up in enough detail to name the work, and three of the five are the same component. That concentration is the whole story of this page.
| Date | Total | What the invoice records |
|---|---|---|
| September 2025 | $457 | KitchenAid, control board replaced |
| October 2024 | $454 | Control board replaced |
| November 2024 | $429 | GE, main control board replaced |
| September 2024 | $428 | Dishwasher repair, component not written up |
| Largest local invoice | $627 | One visit covering an LG stove and an LG dishwasher |
What a Dishwasher Repair Costs, by the Part That Failed
Company-wide, from 2,684 completed dishwasher jobs, and this is the table to price your repair against. Every figure is the full ticket: the part, the labor and the service call added together.
| What failed | Median total | Middle half | Jobs (n) |
|---|---|---|---|
| Spray arm | $283 | $275 to $419 band | 12 |
| Door latch or door switch | $312 | $275 to $419 band | 28 |
| Door gasket | $330 | $275 to $419 band | 42 |
| Water inlet valve | $340 | $275 to $419 band | 37 |
| Drain pump | $350 | $275 to $419 band | 273 |
| Heating element | $362 | $275 to $419 band | 40 |
| Circulation motor | $374 | $275 to $419 band | 122 |
| Control board | $387 | $275 to $419 band | 93 |
| Detergent dispenser | $423 | $275 to $419 band | 27 |
It is worth being precise about what a dishwasher control board actually is, since this city buys more of them than its neighbours.
There are often two: a main control board, usually in the door or under the tub, which sequences the cycle and switches the pumps, the heater and the valve, and a user interface board behind the touch panel, which is just buttons and a display talking to the main board over a ribbon.
A dead panel can be either, or the ribbon between them. Our GE ticket specifies the main control board, which is the one that actually runs the machine. This is also the fault most often guessed at and least often correct on its own: a failed door latch switch at $312 will stop a machine dead and look exactly like a board.
Why Loganville Dishwashers Fail the Way They Do
Three boards in thirteen repairs, and why that is a composition effect $387 COMPANY-WIDE
This is the most important thing on the page and it is a statistical point rather than a mechanical one. Our Loganville dishwasher median of $429 sits $94 above our company-wide median of $335, and $62 above the highest of the neighbouring cities in this cluster.
Nobody here is charged differently. What happened is that three of the thirteen local repairs were control boards, the second most expensive line on the component table, and none of the thirteen was a spray arm at $283 or a door latch at $312. Take three of the most expensive jobs out of a set of thirteen and the middle moves a long way.
We publish the local median because you asked what it costs here, and we publish this explanation because a bare number would have misled you.
This is the deepest dishwasher file in the cluster, and it is still small 39 JOBS
Thirty-nine dishwasher jobs across 36 households is more than any other city in this cluster has given us, and it is worth putting next to our other Loganville files: 78 refrigerators, 57 washers, 24 cooking appliances and 20 dryers. The dishwasher is the appliance households live without for longest, because you can wash by hand for weeks in a way you cannot dry laundry by hand.
Only 7 of the 39 arrived in the last twelve months against 17 in 2023, which is the signature of a machine people defer rather than one that has stopped failing. If yours has been out of action for a while, the useful thing to know is that the most expensive line on the company-wide table is $423.
A dead panel is not automatically a board $312 VERSUS $387
The commonest way a dishwasher dies is that nothing happens when you press start, and the commonest guess is the control board at $387. Before that there is the door latch and its switch at $312: a dishwasher will not run at all unless it can confirm the door is latched, because running one open would put scalding water across a kitchen floor.
There is also the ribbon between the interface board and the main board, and the thermal fuse on the main board that protects it. All of those produce an identical dead machine at very different prices, and separating them is most of what the diagnostic visit is for.
GE and Samsung lead a genuinely mixed file 6 AND 5
Our thirty-nine Loganville dishwasher records carry GE six times, Samsung five, Whirlpool four, Frigidaire four, and LG, KitchenAid and Bosch once each. That is a wider brand spread than any other dishwasher file in this cluster, and it matters practically because the premium and imported machines in it, the Bosch and the KitchenAid, frequently need parts ordered rather than carried, which turns a one-visit repair into two.
Our KitchenAid board job at $457 is exactly that kind of machine. Telling us the brand and model number when you book is the difference between arriving with the part and arriving to find out we need it. These are counts of service calls and not a reliability ranking.
Standing water has four causes and two are not the appliance $350 OR LESS
Water sitting in the sump after a cycle is the most common dishwasher call we take anywhere. The drain pump at $350 is the usual answer. But a blocked filter basket, a kinked or badly looped drain hose, or a garbage disposal knockout plug that was never removed when the dishwasher was installed all produce the identical symptom for no fault of the machine itself.
That last one turns up regularly in houses where the disposal was replaced after move-in, which in a city that grew from 5,435 residents in 2000 to 14,127 in 2020 is a great many of them. A technician follows the whole drain path before condemning a pump.
No single hardness figure exists for this tap, and here that is literal THREE SUPPLIERS
Almost every dishwasher article reaches for hard water, and in Loganville that would be a strange claim to make even if we had a number.
The City of Loganville distributes water but produces none of it: it buys from the City of Monroe, which draws on the John T. Briscoe Reservoir and the Alcovy River, from Walton County, which uses the Lake Varner and Bear Creek reservoirs, and from Gwinnett County on Lake Lanier for emergency use.
At least four reservoirs and two rivers sit behind one tap and the blend can change with the supplier feeding the system. So there is no hardness number on this page. Cloudy glassware and grit on the bottom rack are explained by spray arms, the circulation motor, the filter and the heating element, and all of those are testable in one visit.
See dishwasher not cleaning dishes and, for leaks, dishwasher leaking from the bottom.
🚚 Both the Walton and the Gwinnett side of Loganville are one dispatch zone. If yours is a Bosch or a KitchenAid, give us the model number when you book so the part can be ordered before the visit rather than after it.
Match Your Symptom to the Likely Cause
- Nothing happens when you press start — the door latch and switch at $312 first, then the ribbon to the interface board, then the main control board at $387. We replaced boards locally at $429, $454 and $457, but the latch is cheaper and commoner, so it is tested first.
- Panel lights up but the cycle will not run or will not complete — the main control board, which sequences the pumps, the heater and the valve. Our GE ticket specifies exactly that part at $429.
- Standing water in the bottom after every cycle — drain pump at $350, a blocked filter basket, a looped drain hose, or a disposal knockout plug never removed at installation. All four look identical from the kitchen.
- Dishes come out gritty — spray arms at $283, circulation motor at $374, or a clogged filter recirculating dirty water. See dishwasher not cleaning.
- Dishes come out greasy rather than gritty — the heating element at $362 is not bringing the wash up to temperature, so the detergent never activates.
- Water on the floor while the machine runs — door gasket at $330 or the circulation motor seal at $374. See dishwasher leaking from the bottom.
- It is a Bosch, a KitchenAid or another import — give us the model number when you book. Those machines frequently need parts ordered rather than carried, which is the difference between one visit and two.
Repair or Replace a Dishwasher in Loganville
For everything except the board this is the clearest repair-or-replace case of any appliance we cover.
The drain pump, the spray arms, the door latch, the inlet valve, the heating element and the gasket all sit between $283 and $362 on the company-wide table, against a mid-market replacement that costs more than any of them before you add delivery, disposal of the old unit and the plumbing and electrical connection, which on a built-in is not a plug-in job.
The board is where this city has to think harder than its neighbours, because this is the city that buys them. A control board at $387 to $457 on a machine already past a decade is approaching the installed cost of a new unit, and the rest of the machine is the same age as the board.
On a machine under about eight years old, or on a premium built-in like the KitchenAid in our local file where the replacement has to fit an existing cabinet opening, the board is still clearly the right answer. Between those two we will give you the number and the age and let you decide, rather than steering it.
Expected service life is in how long dishwashers last and the framework in the repair or replace guide.
Discounts Applied Automatically
Priority Membership
$179 a year, five diagnostics and priority slots
- Five free diagnostic visits a year, a $495 value
- Priority scheduling with 24 to 48 hour response
- $30 off labor on every repair
- Extended warranty on all Bozmanfix work
What Atlanta Area Customers Say About Bozmanfix
“Very professional work. We called for a dishwasher repair and it was done within just a few days. Eugene was prompt and speedy, and made sure to keep our space tidy.”
“Denis was absolutely wonderful. He took the time to thoroughly inspect my dishwasher and give his diagnosis. Repair was done within the next day quickly and efficiently.”
“Max from Bozmanfix came out about 3 hours after our first call and had the dishwasher apart and then fixed within 45 mins.”
“In and out! I am so glad. I tried to fix the dishwasher myself and I wish I called sooner.”
Loganville Dishwasher Repair, Answered
How much does dishwasher repair cost in Loganville, GA?
The local median is $429 once a part is replaced, from 39 dishwasher jobs inside Loganville of which 13 involved a part being fitted. That is the highest dishwasher median of the six cities in this cluster and it is a composition effect rather than a local rate: three of the thirteen repairs were control boards.
Our company-wide median across 2,684 dishwasher jobs is $335, and that table is what you should price your own repair against.
Why is dishwasher repair more expensive in Loganville than nearby?
It is not. Every household pays the same price for the same part. A dishwasher control board is $387 all in on our company-wide table against $350 for a drain pump and $283 for a spray arm, and three of our thirteen local repairs happened to be boards while none was a spray arm or a door latch.
Take three of the most expensive jobs out of a set of thirteen and the middle moves a long way. We publish the local median because you asked, and the explanation because a bare number would mislead you.
Nothing happens when I press start. Is that the control board?
Possibly, and it is the guess almost everyone makes. Before it there is the door latch and its switch at $312: a dishwasher will not run at all unless it can confirm the door is latched, because running one open would put scalding water across the kitchen floor.
There is also the ribbon between the interface board and the main board, and the thermal fuse that protects the board. All of them produce an identical dead machine at very different prices.
Does a dishwasher have more than one board?
Usually two. The main control board, generally in the door or under the tub, sequences the cycle and switches the pumps, the heater and the valve. The user interface board behind the touch panel is buttons and a display talking to the main board over a ribbon.
A dead panel can be either, or the ribbon between them. Our GE ticket in this city specifies the main control board, which is the one that actually runs the machine.
Why is there standing water in the bottom of my dishwasher?
The drain pump at $350 all in is the usual answer and the most replaced dishwasher part in our entire company file.
But a blocked filter basket, a kinked drain hose, or a garbage disposal knockout plug that was never removed when the dishwasher was installed all produce exactly the same symptom for no fault of the machine itself. That last one is common in houses where the disposal was replaced after move-in.
Is hard water ruining my dishwasher in Loganville?
We do not publish a hardness figure, and in this city a single number would be a strange thing to publish even if we had one.
The City of Loganville distributes water but produces none of it: it buys from the City of Monroe, from Walton County and from Gwinnett County, drawing between them on at least four reservoirs and two rivers, so the blend reaching your street can change with the supplier feeding the system.
Cloudy glassware and grit are explained by spray arms, the circulation motor, the filter and the heating element.
Do you repair Bosch and KitchenAid dishwashers?
Yes, and both are in our Loganville file, including a KitchenAid control board replacement at $457. The practical difference with premium and imported machines is parts availability: they frequently have to be ordered rather than carried on the van, which turns a one-visit repair into two.
Telling us the brand and model number when you book is the difference between arriving with the part and arriving to find out we need it.
More Appliance Repair in Loganville, GA
The other appliances in the house have their own Loganville pages, each with its own local job count and its own component table.
Appliance Repair in Loganville Serving Loganville, GA and the wider Atlanta area → View our full service areaBook a Loganville Dishwasher Technician
Latches and ribbons tested before boards are condemned, a live cycle run and watched, the $99 diagnostic applied to the repair and a 90-day parts and labor warranty behind the work.