Washer Repair Conyers GA
Washer repair in Conyers, GA has a median cost of $394 once a part is replaced, and $243 across all completed visits. Those come from 111 washing machine jobs we have run inside Conyers for 110 households, 89 of which closed as paid work.
The most useful thing on this page is how tightly the repairs cluster: the 49 visits that needed a part landed between $313 and $446, so a Conyers washer repair sits in a narrow, predictable band.
A Conyers washer repair is one of about five jobs that all cost roughly the same, which is why the quote at the door rarely surprises anyone. This is also current work rather than history: 59 of the 111 jobs are from the last twelve months and 35 fall in 2026 alone.
Washer Repair in Conyers, GA
Will not drain, will not spin, banging or walking on spin, stops mid-cycle, flashing a code, leaking. Top-load, front-load and stacked pairs, all three Conyers ZIP codes, total confirmed before the work starts.
What a Washer Repair Costs, by the Part That Failed
The Conyers median tells you where the city lands. The component table explains why almost every washer repair here costs about the same thing once a part is genuinely needed.
It is built from 4,763 completed washing machine jobs across our whole service area, because 49 local with-a-part jobs cannot honestly price nine separate components. Every figure is the full ticket: the part, the labor and the service call added together.
| What failed | Median total | Jobs (n) |
|---|---|---|
| Drive belt | $341 | 74 |
| Door lock or lid switch | $351 | 143 |
| Water inlet valve | $362 | 137 |
| Shock absorbers or suspension rods | $367 | 195 |
| Tub bearing | $380 | 11 |
| Drain pump | $381 | 213 |
| Drive motor | $387 | 81 |
| Motor control board | $436 | 163 |
| Front-load door boot seal | $450 | 49 |
This is the flattest price table of any appliance we service, and the reason is arithmetic rather than generosity: a belt is a $30 part and a drive motor is a $200 part, but both bills are mostly the visit and the hour or two it takes to get the machine away from the wall and open.
Two things are worth knowing about how Conyers sits against that table. Our local drain pump jobs ran $337, $455, $466 and $479, three of the four above the company median of $381, which is what happens when a pump has to come out of a machine that has been leaking into its own base for a while.
And the two most expensive mechanical repairs in our Conyers washer record are not on the table at all: a Maytag transmission and drive pulley at $503 and a clutch and transmission at $406. Those are top-loader jobs, they are a bigger strip-down than anything in the list above, and they are the point where we start talking about replacement instead.
The Conyers city hub puts the washer alongside the other five appliances.
Why Conyers Washers Fail the Way They Do
Suspension is the signature repair in this city 5 OF 21 NAMED JOBS
Of the 21 Conyers washer invoices that name a specific component, five are suspension: rods on a Kenmore at $436, rods and a drive block on a Maytag at $398, rods on a Whirlpool at $394, rods at $390 and a Samsung logged simply as “suspension is broken” at $338.
No other single repair repeats that often in our local washer record.
Suspension rods are the four damped struts that hang the tub inside a top-load washer, and they wear out from the load rather than from age: a heavy, wet, unbalanced wash, a duvet or a bath mat that has slumped to one side, throws the tub against its own travel limits a few thousand times and the damping wears out of the rods.
Then the machine bangs, walks across the floor and eventually throws an unbalance error and refuses to spin. What matters for your money is that the same symptom, banging on spin, is also produced by a machine that simply is not level, which takes a minute with a spirit level and costs you nothing.
So a technician checks the feet before quoting rods, and if you want to check them yourself, put a hand on each corner before you book.
The drain side, and why our pumps ran above the average $337 TO $479
Drain work is the second most repeated repair here: four drain pumps at $337, $455, $466 and $479, and two drain hoses at $277 and $406.
Rockdale Water Resources is the sole water and sewer supplier in the county, so unlike the unincorporated parts of Fayette or Coweta County there is no septic drainfield to rule out first and a Conyers washer that will not drain has its fault inside the machine, in its pump filter, its hose or its standpipe.
That is good news, because the first two of those are cleared at the diagnostic and cost you nothing beyond the visit.
The pumps that did need replacing ran above the company-wide $381 for a reason worth knowing: a drain pump usually fails gradually, so by the time the machine stops draining altogether it has often been weeping into its own base for weeks, and a pump that has to come out of a wet, corroded chassis is a longer job than one changed early.
If your washer has started leaving a cupful in the drum at the end of a cycle, that is the cheap moment to call. Background on the free part is in why a washer will not drain.
About five repairs cover most of what a Conyers washer needs 49 OF 89
A $99 visit here buys one of three outcomes, and all three are worth the money: a free fix such as a levelling adjustment or a cleared pump filter, a firm quote you can accept on the spot, or a straight answer that this particular machine is not worth the parts.
Our own record shows why the third matters: one Conyers visit found a spider arm damaged by metal fatigue and corrosion, a real and terminal fault on a front-loader, and the honest answer was a new machine rather than a repair you would regret. The third one is the one people are most grateful for a year later.
Unlike the refrigerator, the badge does not predict anything NO BRAND EFFECT
Our Conyers washer work is split almost evenly across brands: Whirlpool 14 tagged jobs, GE 12, Maytag 12, Samsung 12, then LG 5, Frigidaire 5, Amana 3 and Kenmore 2. More interestingly, the badge barely changes what we find. That is unlike refrigerators in this same city, where the brand does shift the diagnosis.
Washers are simply more mechanical: every brand’s tub hangs on something, drains through something and locks a door, and they wear the same way. The one practical brand note is about waiting rather than paying.
Whirlpool, GE, Maytag, Frigidaire, Amana and Kenmore parts ride on the van, so those repairs usually finish on the first visit; Samsung and LG electronics are the ones we order, and our largest Conyers washer invoice is a Samsung inverter board at $697.
Boards and stacked pairs are the top of the range $697 · $586
Six of the 89 paid Conyers washer jobs closed above $500, and they are the two situations that break out of the flat table. The first is electronics: a Samsung inverter board at $697 and a control board at $438, against a company-wide $436 for a motor control board.
A washer is switched off most of the day but its board is on standby around the clock, so when power returns after an outage the board takes the jolt, and Conyers sits on two different electricity systems, Georgia Power and Snapping Shoals EMC, which means neighbouring streets can be restored at different moments.
The second is configuration: an LG stacked washer-dryer at $586. On a stacked pair the diagnostic is $150 rather than $99, because the dryer has to come off the washer or the tower out of its closet before anything can be reached, and we tell you that before the visit rather than on the day. Notes on the electronics side are in control boards and error codes.
Where the work is, and where it is not 55 · 32 · 24
The three Conyers ZIP codes give us very different amounts of washer work: 55 jobs in 30094 on the south and southwest side, 32 in 30013 toward the Newton County line and 24 in 30012 on the west and north side.
Prices barely differ, $392 with a part replaced in 30094 on 28 jobs, $395 in 30013 on 15 and $376 in 30012 on only 6, so this is a volume story rather than a price story, and the likeliest reason is tenure rather than machines: 30094 is 79 percent owner-occupied while 30012 has 38 percent renters, and a washer in a rental usually reaches a landlord rather than a technician.
On samples that size the difference is too small to build a theory on, so we are showing you the counts rather than a conclusion.
🚚 59 Conyers washer jobs in the last twelve months, and Whirlpool, GE, Maytag and Frigidaire suspension, pump and valve parts ride on the van. A washer full of wet laundry gets scheduled ahead of one that merely squeaks.
Match Your Symptom to the Likely Cause
- Bangs, walks across the floor or refuses to spin a heavy load — level the machine first, that part is free, then suspension rods, the most repeated repair in our Conyers record at $338 to $436, or a drive block on a Maytag. Company-wide 195 jobs at $367. Also washing machine out of balance.
- Water still in the drum at the end of the cycle — the pump filter or a kinked hose, cleared at the diagnostic, otherwise the drain pump at $337 to $479 here, or the drain hose itself at $277 to $406. Call at the cupful-left-in-the-drum stage rather than the full-drum stage. See why a washer will not drain.
- Fills and agitates but the drum never spins on a top-loader — a lid switch or door lock at $351, a belt at $341, or the expensive end of this city’s record, a clutch or transmission at $406 to $503. The cheap causes are checked first, always.
- Will not start, lights up and does nothing, or flashes a code after an outage — a door lock that has failed electrically, or the control board: $438 on one Conyers job and $697 for a Samsung inverter board. Boards are tested before they are condemned.
- Filling slowly, or only on one temperature — the water inlet valve, $446 and $447 on Conyers invoices against a company median of $362. Rockdale’s water is surface water from Randy Poynter Lake and its mineral load shifts with the season, so a valve screen clogs on its own schedule rather than a predictable one.
- Leaking onto the laundry room floor — on a front-loader the door boot seal at $450, or debris trapped in the boot, which is free; on a top-loader a hose or the pump. Company-wide, leaks run a median of $354 across 482 jobs.
- Grinding or roaring on spin that gets worse every week — a tub bearing at $380, or the drive motor at $387. Catching it early is the difference between a bearing and a machine that has chewed up its own tub. Also what appliance noises mean.
Repair or Replace, on the Conyers Numbers
For most of what fails on a Conyers washer this is an easy decision. At $394 with a part, against a comparable new machine plus delivery, haul-away and installation, repair wins on anything under about eight years old, and the flat component table means you are almost never quoted a repair that approaches the price of a new machine, which is what makes refrigerator compressors a genuine dilemma.
Suspension rods at $394 on a machine that otherwise works are simply worth doing. The line sits in two places in this city. The first is the transmission: at $406 to $503 on a top-loader past about ten years, with worn rods likely to follow, the parts start to stack up and we will say so.
The second is the front-load spider arm, the aluminium spider that carries the drum, which is what one of our Conyers diagnostics found corroded and fatigued; there we put the repair total next to the price of a comparable new machine so the arithmetic is yours.
Company-wide, that comparison is where most replace decisions get made, and the figures behind it are on the national page. Stacked pairs run the other way, because replacing one means matching a closet cutout, so repair wins on them longer. The lifespan tables are in how long washing machines last and the arithmetic in the repair versus replacement guide.
Discounts Applied Automatically
Priority Membership
$179 a year — five diagnostics, priority slots
- Five free diagnostic visits a year, a $495 value
- Priority scheduling with 24 to 48 hour response
- $30 off labor on every repair
- Extended warranty on all Bozmanfix work
What Atlanta Customers Say About Bozmanfix
“Eugene came out to take a look at our washer. He fixed it on the spot. He was professional, quick, and easy.”
“Denis fixed my washer and he was top notch! Perfect gentleman and absolute professional!”
“Yuriy did an excellent job repairing our washing machine.”
“These guys are quick to respond and even quicker to repair!! The individual that came out had the part I needed on hand.”
Washer Repair in Conyers — Questions We Get
How much does washer repair cost in Conyers, GA?
The median is $394 once a part is replaced, and $243 across all completed visits, from 89 paid washer jobs inside Conyers. The middle half of with-a-part jobs runs $313 to $446.
By component, company-wide and including the part, the labor and the service call: drive belt $341, lid switch or door lock $351, water inlet valve $362, suspension $367, tub bearing $380, drain pump $381, drive motor $387, control board $436, front-load door boot seal $450.
My washer bangs and walks across the floor. Is that expensive?
The first check is free and it is the one to do before booking: put a hand on each corner and rock the machine, because feet that are not level or not locked produce banging, walking and unbalance errors with nothing broken, and so does a duvet that has slumped to one side of the drum.
If it is level and still bangs, it is the suspension, which is the most repeated repair in our Conyers record: rods ran $338 to $436 on five local jobs, against a company-wide median of $367. On a front-loader the same noise can be a worn drum bearing, around $380, which is rarer.
What does the $99 diagnostic buy me on a washer?
One of three answers, and the fee is the same for all of them. Either the technician clears the fault on the spot, which on a washer is often a levelling adjustment or a packed pump filter. Or you get a firm total for the repair before any work starts, with the $99 applied to it.
Or you get the straight version on a machine that is not worth the parts: one Conyers visit found a spider arm damaged by metal fatigue and corrosion, and on a front-loader the honest answer there is a new machine. Every completed repair carries a 90-day parts and labor warranty.
My washer will not drain. Could it be the sewer line or a septic tank?
Not a septic tank. Rockdale Water Resources is the sole supplier of both water and sewer service in Rockdale County, so unlike the unincorporated parts of Fayette or Coweta County there is no drainfield to eliminate first. A Conyers washer that will not drain has a clogged pump filter, a kinked or over-inserted drain hose, or a failed pump or hose, and the first two are cleared on the diagnostic.
Our local drain pump jobs ran $337 to $479 and drain hoses $277 to $406. If the laundry or kitchen sink is slow at the same time, that is a shared drain line and a plumber’s job, and we will tell you rather than replace a pump.
Which washer brands do you see most in Conyers?
The work is split unusually evenly: Whirlpool 14 tagged jobs, GE 12, Maytag 12 and Samsung 12, then LG 5, Frigidaire 5, Amana 3 and Kenmore 2. Unlike refrigerators in this same city, the badge does not predict much about the diagnosis.
What it does predict is waiting: Whirlpool, GE, Maytag, Frigidaire, Amana and Kenmore parts ride on the van, while Samsung and LG electronics are ordered. Our largest local washer invoice is a Samsung inverter board at $697.
Do you repair stacked washer-dryer units in Conyers?
Yes. The diagnostic on a stacked pair is $150 rather than $99, because the dryer has to come off the washer, or the tower out of its closet, before anything can be seen, and that fee is applied to the repair like any other. Our largest stacked job here is an LG at $586.
We tell you about the $150 when you book rather than on the day, and stacked pairs are worth repairing for longer than freestanding machines, because replacing one means matching a closet cutout as well as buying two appliances.
Is a washer worth repairing, or should I replace it?
At the Conyers median of $394 repair wins on almost anything under about eight years old, and because every component lands between $341 and $450 you are rarely quoted a repair close to the price of a new machine. Two cases go the other way.
A top-loader past about ten years needing a transmission, $406 to $503 in our local record, with worn suspension likely to follow, is where the parts start to stack up. And a front-loader with a corroded spider arm is a new machine, not a repair.
In both cases we put the repair total next to the price of a comparable new washer, so the arithmetic is yours to make.
More Appliance Repair in Conyers, GA
Each page is built on the jobs we have actually run in this city, with the local price band and the failure patterns for that appliance.
Appliance Repair in Conyers GA — all services and city pricingServing Conyers, GA and the wider Atlanta area → View our full service areaBook Washer Repair in Conyers
111 washer jobs on record in this city, 59 in the last twelve months. $99 diagnostic applied to the repair, $150 on stacked pairs, 90-day parts and labor warranty, all three ZIP codes.