Dryer Repair Conyers GA
Dryer repair in Conyers, GA has a median cost of $378 in Bozmanfix records once a part is replaced. Those come from 45 dryer jobs we have run inside Conyers for 42 households, 29 of which closed as paid work.
The two figures sit only $26 apart, and that is the whole character of a dryer call in this city: the median you see here is a fair guide to your ticket.
A dryer that has stopped here is almost always genuinely broken. This is also the freshest record we hold for any appliance in Conyers, because every one of these 45 jobs is dated May 2025 or later and 39 of them fall in the last twelve months.
Dryer Repair in Conyers, GA
No heat, clothes still damp after a full cycle, drum will not turn, squealing or thumping, shuts off early, will not start. All three Conyers ZIP codes, total confirmed before the work starts.
What a Dryer Repair Costs, by the Part That Failed
A dryer that stops here usually has a real fault, so you are very likely to land on one of the lines below, which makes this table more useful here than the city median is.
It is built from 4,559 completed dryer jobs across our whole service area. Every figure is the full ticket: the part, the labor and the service call together.
| What failed | Median total | Jobs (n) |
|---|---|---|
| Door switch | $324 | 54 |
| Drive belt | $322 | 259 |
| Thermal fuse | $332 | 84 |
| Drum rollers or idler pulley | $350 | 218 |
| Cycling or high-limit thermostat | $349 | 144 |
| Blocked vent cleared | $357 | 43 |
| Heating element | $367 | 360 |
| Blower wheel | $372 | 22 |
| Drive motor | $394 | 55 |
| Control board | $507 | 21 |
A dryer is the simplest machine in the house, a drum, a motor, a belt, a heat source and a fan, and the table shows it: everything except the control board lands inside $75. Conyers tracks that closely, with one detail at each end worth naming.
At the top, our largest local dryer invoices are a Samsung drive motor at $653 and a control board at $488, and an LG stacked washer-dryer at $586 where the pair had to come apart before anything could be reached.
At the bottom, two Conyers jobs came in below every line in the table: fuses and sensors at $280, and sensors with a thermostat on a Whirlpool at $285. Those are the cheap, boring, unglamorous repairs that a dryer needs most often, and they are worth knowing about because people talk themselves out of calling on the assumption that a dryer that will not heat means a big bill.
The Conyers city hub puts the dryer alongside the other five appliances in the city.
Why Conyers Dryers Fail the Way They Do
The lint is the cause, not the symptom, and the clean-out is in the job CLEANING INCLUDED
Three of our Conyers belt and pulley invoices carry the same parenthesis in the technician’s own words: a GE belt replacement at $352 “(cleaning included)”, a Maytag belt at $355 “(cleaning concluded)”, a Samsung belt and pulley at $423 “(cleaning included)”. A fourth job is nothing but a clean: “Unit cleaning”, $328.
That is not an upsell bolted onto a repair, it is the order of events reversed from how most people picture it. Lint does not only collect in the screen; it packs the ducting, the blower housing and the cabinet floor around the drum.
Restricted airflow means the heat cannot leave, the drum runs hotter and drags, and the belt and idler pulley wear out early while the element cooks itself.
Replace the belt and leave the lint, and you have bought yourself another belt in a year or two. That is why our technicians clear the machine out as part of the mechanical repair here, and why company-wide a “blocked vent cleared” job on its own has a median of $357 across 101 jobs, the same money as a thermostat.
Element and belt are two thirds of the work 6 OF 12 NAMED JOBS
Of the twelve Conyers dryer invoices that name a component, six are the same two parts. Three heating elements at $398, $404 on a Maytag and $420. Three belt or pulley jobs at $352, $355 and $423.
The rest of the record is one of each: a Samsung drive motor at $653, a control board at $488, a Maytag blower wheel at $313, sensors and a thermostat at $285, fuses and sensors at $280, and the standalone clean at $328.
That distribution is the reason a dryer diagnosis is quick and a dryer quote is rarely a surprise. No heat is an element, a fuse or a thermostat. No tumble is a belt or a motor. A rattle from the back is the blower wheel.
There is very little middle ground where a dryer can be mysteriously unwell, which is why the technician can usually name the part on the first visit.
Every dryer job we have in this city is electric 0 OF 45
Not one of our 45 Conyers dryer jobs involved gas work: no igniter, no gas valve coils, no gas line. That is a statement about our record rather than about every laundry room in Rockdale County, and it is worth saying because it changes the diagnosis of the single most common complaint.
On a gas dryer, “runs but no heat” is usually the igniter, and in cities where we do a lot of gas work that is the first thing we test.
On the electric machines we see in Conyers, the same symptom is a heating element, a thermal fuse or a thermostat, and there is one thing worth telling us at booking: an electric dryer runs on a double breaker, so if only one half has tripped the drum will turn happily while the element stays stone cold.
Tell us at booking whether the panel shows a tripped breaker. If you do have a gas dryer and you smell gas, leave the house and call the gas utility first, as set out in our gas appliance safety guide.
A current record, and a growing one SINCE MAY 2025
Our Conyers dryer record runs from 22 May 2025 to July 2026, and it is growing.
It matters for two reasons. First, everything on this page describes machines as they are failing now, not a picture assembled over five years, so the parts we quote are the parts we are actually fitting this year.
Second, 23 of the jobs fall in 2025 and 22 in the first seven months of 2026, which means the pace has roughly doubled and Conyers dryers are now a regular part of the week rather than an occasional call.
Dryer prices differ by ZIPTHREE ZIP CODES
The three ZIP codes split the work almost evenly at the top, 19 dryer jobs in 30013 and 19 in 30094 against 7 in 30012, and prices differ by ZIP: a with-a-part median of $413 in 30013 on ten jobs against $356 in 30094 on ten and $319 in 30012 on four.
The honest summary is the one the whole city record supports: wherever you are in Conyers, a dryer that has stopped working is very likely to need a part, and the part is very likely to cost between $320 and $440.
The board is the one repair that a storm causes $488
A dryer sits idle most of the day, but its control board is on standby whenever the machine is plugged in, so a surge or a hard restart after an outage reaches it.
Conyers is served by either Georgia Power or Snapping Shoals EMC depending on the address, which means neighboring streets can lose and regain power at different moments, and the city has a recent hard example: an EF-2 tornado with maximum winds of 115 mph touched down southwest of Conyers late on 2 April 2024 and tracked north of Olde Town, leaving more than 2,300 Georgia Power customers in Rockdale without power the following morning.
Our one Conyers dryer board came to $488 against a company-wide median of $507, and it is the only line in the table above $400. Before condemning one the technician tries a reset at the breaker, because a board that has locked itself out after an outage sometimes clears, and then the diagnostic is all you pay.
🚚 39 Conyers dryer jobs in the last twelve months, and the elements, belts, rollers and thermostats for Whirlpool, GE, Maytag and Frigidaire ride on the van, so most of these finish on the first visit.
Match Your Symptom to the Likely Cause
- Drum turns, no heat at all – tell us at booking whether the double breaker has tripped; otherwise a heating element, $398 to $420 on Conyers jobs, a thermal fuse at $332, or a thermostat. Two local jobs did it for $280 and $285 with fuses and sensors. Company-wide this is the biggest dryer category by far, 1,103 jobs. Read dryer not heating.
- Heats, but clothes come out damp after a full cycle – restricted airflow: the lint screen, the vent hose, or a packed cabinet, cleared at $328 to $350, or a failing cycling thermostat at $349. Company-wide 414 jobs at a median of $375. Also dryer not drying fast.
- Motor hums or nothing turns – a drive belt at $322, our local belt jobs $352 to $423 with the machine cleaned out, or the drive motor, which on one Conyers Samsung came to $653. A door switch at $324 gives silence with no hum at all.
- Squealing or thumping as the drum turns – drum rollers or the idler pulley at $350, and if the noise is a rattle from behind rather than a squeal from the drum, the blower wheel, $313 on a Maytag here. The largest noise category we service: 662 jobs company-wide.
- Shuts off partway through a cycle, or the cabinet gets very hot – the high-limit thermostat has tripped, and the reason is almost always airflow rather than the thermostat itself, so both get dealt with or you will see us again.
- Dead after a storm, or the panel lights and nothing runs – a reset at the breaker comes first, then the control board at $507 company-wide, $488 on our Conyers job. Two power systems serve this city and they come back at different moments.
- A stacked pair, whatever the symptom – the same parts and prices plus the time to get the tower apart, which is why the diagnostic is $150 rather than $99 and why our LG stacked job here reached $586.
Repair or Replace, on the Conyers Numbers
This is the easiest repair-or-replace call of any appliance in this city, and the numbers say so plainly. At $378 with a part, against a comparable new dryer plus delivery, haul-away and a new vent connection, repair wins on anything under about twelve years old, and a Whirlpool or Maytag dryer running well at fifteen with a fresh belt, rollers and element is an ordinary sight.
The two cases that go the other way are a dryer past fifteen years needing a drive motor on top of a worn drum, where the parts stack up, and a machine that has been run for years with a blocked vent, because sustained overheating ages everything inside the cabinet at once.
Stacked pairs are worth repairing for longer than freestanding machines, since replacing one means matching a closet cutout as well as buying two appliances. The service-life tables are in how long dryers last, and the arithmetic in the repair versus replacement guide.
Discounts Applied Automatically
Priority Membership
$179 a year – five diagnostics, priority slots
- Five free diagnostic visits a year, a $495 value
- Priority scheduling with 24 to 48 hour response
- $30 off labor on every repair
- Extended warranty on all Bozmanfix work
What Atlanta Customers Say About Bozmanfix
“Bozman fix fixed my issue with my dryer.”
“Amazing! I was informed when the technician was en route to my home. He came in diagnosed the issue gave me a price fixed my dryer and was done in about an hour. I will use them anytime I need any repairs and will suggest them to anyone who needs repairs.”
“They were very quick to respond and fix our issue with our dryer. Definitely recommend.”
“The Bozmanfix technicians arrived on time and were friendly. The dryer works again and even better than before!”
Dryer Repair in Conyers – Questions We Get
How much does dryer repair cost in Conyers, GA?
The Bozmanfix median is $378 once a part is replaced, from 29 paid dryer jobs inside Conyers. The middle half of with-a-part jobs runs $320 to $439.
By component, company-wide and including the part, the labor and the service call: door switch $324, drive belt $322, thermal fuse $332, drum rollers $350, thermostat $349, blocked vent cleared $357, heating element $367, blower wheel $372, drive motor $394, control board $507.
My dryer turns but does not heat. What is it likely to be?
Tell us at booking whether the breaker panel shows a trip, because an electric dryer runs on a double breaker and if only one half has tripped the drum turns while the element stays cold. Otherwise it is the heating element, $398 to $420 on our Conyers jobs, a thermal fuse at $332, or a thermostat, and two local jobs solved it for $280 and $285 with fuses and sensors.
Note that none of our 45 Conyers dryer jobs involved gas, so on the machines we see here the igniter is not part of this conversation.
Why do you clean the dryer out as part of a belt repair?
Because the lint is the cause and the belt is the symptom. Lint packs the ducting, the blower housing and the cabinet floor, not just the screen. Restricted airflow traps the heat, the drum runs hotter and drags, and the belt and idler pulley wear out early while the element cooks.
Three of our Conyers belt jobs say so in the technician’s own note, “cleaning included” or “cleaning concluded”, at $352, $355 and $423, and one Conyers job was a clean-out on its own at $328. Replace the belt and leave the lint and you will need another belt.
What does a Conyers dryer diagnostic tell you?
A dryer has almost no middle ground, so the technician can usually name the failed part on the first visit and give you the total before any work starts.
No heat is an element, a fuse or a thermostat; no tumble is a belt or a motor; a rattle from the back is the blower wheel. The simple causes do exist – a half-tripped breaker, a crushed vent hose, a lint screen sealed with dryer-sheet residue – and we check them first, but they are the minority here rather than the norm.
Do you repair stacked washer-dryer units in Conyers?
Yes. The diagnostic on a stacked pair is $150 rather than $99, because the dryer has to come off the washer or the tower out of its closet before anything can be seen, and that fee is applied to the repair like any other. Our largest local stacked job is an LG at $586.
We tell you about the $150 when you book, not on the day, and stacked pairs are worth repairing for longer than freestanding machines because replacing one means matching a closet cutout and buying two appliances at once.
Which dryer brands do you see most in Conyers?
The Bozmanfix record is small and evenly spread: Whirlpool 5 tagged jobs, GE 4, Maytag 3, Samsung 3, LG 2, Kenmore 1 and Frigidaire 1. Whirlpool, GE, Maytag, Frigidaire and Kenmore share most of their mechanical parts across model years, and elements, belts, rollers and thermostats for them ride on the van, so those repairs usually finish on the first visit.
Samsung and LG dryers are more electronic and their motors and boards are the parts we order: our two largest local dryer invoices are a Samsung drive motor at $653 and an LG stacked unit at $586.
Is a twelve-year-old dryer worth repairing?
Usually yes. At the Conyers median of $378 a dryer under about twelve years old is a straightforward repair, and Whirlpool or Maytag machines running well at fifteen with a new belt and element are common.
The cases for replacing are a dryer past fifteen years needing a drive motor as well as a worn drum, and one that has run for years behind a blocked vent, because sustained overheating ages everything in the cabinet at once.
More Appliance Repair in Conyers, GA
Each page is built on the jobs we have actually run in this city, with the local price band and the failure patterns for that appliance.
Appliance Repair in Conyers GA – all services and city pricingServing Conyers, GA and the wider Atlanta area → View our full service areaBook Dryer Repair in Conyers
45 dryer jobs on record in this city, 39 of them in the last twelve months. $99 diagnostic applied to the repair, $150 on stacked pairs, 90-day parts and labor warranty, all three ZIP codes.