Dryer Repair St. Johns FL
If your dryer has stopped in St. Johns, it is almost certainly genuinely broken. 6 of our 7 paid dryer visits in ZIP 32259 ended with a part fitted, 85.7 percent, against 56.5 percent on washers in the same laundry rooms.
We are being straight with you about the sample though: 11 dryer jobs is the thinnest pool of any appliance in this cluster, so the prices below come from our company-wide book of 4,218 completed dryer repairs, where the median with a part replaced is $352. $99 diagnostic, applied to the repair, 90-day parts and labor warranty.
Dryer Repair in St. Johns, FL
No heat, clothes still damp after a full cycle, will not tumble, will not start, squealing or thumping, shutting off part-way. Gas and electric. Total before we start.
What Dryer Repair Costs in St. Johns, by Component
We would rather label a thin sample than dress it up. Six St. Johns dryer jobs had a part replaced, which is not enough to publish a local component breakdown or to claim this ZIP is different from anywhere else.
So the local row is shown for completeness with its job count attached, and every component figure below it comes from our company-wide book of 4,218 completed dryer repairs. All figures are parts, labor and the service call together.
| Repair | Median total | Source | Jobs behind it (n) |
|---|---|---|---|
| Any dryer repair, part replaced | $401 | St. Johns 32259 · thin sample | 6 |
| Any dryer repair, part replaced | $352 | Company-wide | 4,218 |
| Door switch | $321 | Company-wide | 54 |
| Drive belt | $322 | Company-wide | 259 |
| Thermal fuse | $332 | Company-wide | 84 |
| Drum rollers or idler pulley | $349 | Company-wide | 218 |
| Cycling thermostat | $350 | Company-wide | 144 |
| Blocked vent cleared | $350 | Company-wide | 43 |
| Heating element | $362 | Company-wide | 360 |
| Blower wheel | $368 | Company-wide | 22 |
| Drive motor | $394 | Company-wide | 55 |
| Control board | $478 | Company-wide | 71 |
| Diagnostic visit only | $99 | Flat rate | — |
Two lines in that table deserve to be read next to each other. Clearing a blocked vent runs $350 and replacing a heating element runs $362, twelve dollars apart, and they are connected: a restricted vent is the most common reason a heating element burns out in the first place.
Trapped heat drives the high-limit thermostat and the element beyond what they are designed for, the element eventually fails, and if the vent is not dealt with at the same time the replacement follows the original. That is the single most useful thing on this page.
When we replace an element we check the vent run in the same visit, because otherwise you are buying the same repair twice. Our full component data across 29,315 repairs is in appliance repair cost by component.
Why St. Johns Dryers Fail the Way They Do
ZIP 32259 is newer single-family housing, 25,181 units, mostly with the laundry room inside the conditioned envelope rather than in a garage. That layout has one consequence that matters a great deal for a dryer, and our own numbers point at it.
This is our smallest local sample, and we will not pretend otherwise 11 JOBS
Eleven dryer jobs in 32259, seven of them paid, six with a part replaced. That is enough to observe a pattern and nowhere near enough to publish a local component price, so we have not.
It is also worth noting that 9 of those 11 fall in the last twelve months, meaning nearly our entire dryer history in this ZIP is recent rather than accumulated, which is another reason to treat local figures here as provisional.
Everything priced on this page above the first row comes from thousands of repairs across our whole territory. When the local pool is large enough to say something specific about St. Johns dryers, we will publish that instead.
The vent costs the same as the element, and it is what kills the element $350 AGAINST $362
Clearing a blocked vent runs a $350 median across 43 company jobs and a heating element runs $362 across 360. They are within twelve dollars of each other, and the causal arrow runs one way: a restricted vent traps heat, the high-limit and cycling thermostats work harder, and the element fails early.
Longer vent runs are the norm in newer interior laundry rooms, because the duct has to travel from the middle of the house to an outside wall, sometimes with two or three elbows. Every extra foot and every elbow adds restriction. If we replace an element and leave the vent alone, you will see us again.
The lowest part-fitted share of anything we service 79.5 PERCENT COMPANY-WIDE
Across our entire book, dryers end with a part fitted 79.5 percent of the time. Every other appliance is higher: washers 41.0 percent, dishwashers 40.7 percent, freezers 43.9 percent, refrigerators 35.2 percent. In St. Johns the local dryer figure is 14.3 percent on seven visits.
We do not have a confident explanation for why dryers sit so far below everything else and we are not going to invent one. What we can say is the practical consequence: a dryer visit is the one where the $99 is most likely to turn into a repair rather than an explanation, so the diagnostic being credited against the work matters more here than anywhere else.
Damp clothes and no heat are the same call from our side 1,195 JOBS
Company-wide, jobs logged as no heat number 969 with a $368 median and jobs logged as damp clothes number 226 at $365. From a technician’s point of view those are one problem with two descriptions, and the shortlist is identical: heating element, thermal fuse, cycling thermostat, or airflow.
On a gas dryer the ignition side joins that list — we service gas and electric both, but our sample of gas-specific component replacements is too small to publish medians for, so we will not put numbers on it. Background reading is in dryer not heating and how a dryer heating element is replaced.
9 of our 11 St. Johns dryer jobs fall in the last twelve months. If your dryer has stopped, the odds are strongly that there is a real part behind it. Book online or call (954) 902-6229.
Where in St. Johns We See This Work
One ZIP code with several accepted names. USPS lists Saint Johns as the primary city for 32259 and accepts Fruit Cove, Julington Creek, Switzerland and Jacksonville for the same delivery area.
| Name on the address line | All our jobs in 32259 | Dryer jobs |
|---|---|---|
| Saint Johns · primary city | 107 | 8 |
| Jacksonville · accepted alias | 157 | 2 |
| Fruit Cove · accepted alias | 32 | 1 |
| Julington Creek · accepted alias | 4 | 0 |
| Switzerland · accepted alias | Covered, no jobs logged under this spelling | |
Same code, same route, same price, no travel surcharge between the names. The full ZIP-wide picture is on appliance repair in St. Johns.
Around St. Johns
The metro-level page is dryer repair in Jacksonville FL, with the whole territory on appliance repair in Jacksonville. Neighbouring clusters with their own dryer pages are Ponte Vedra Beach, Orange Park, Jacksonville Beach and Fernandina Beach. If it cannot wait, same-day appliance repair in Jacksonville covers the scheduling, and typical service life is in how long dryers last.
Match Your Symptom to the Likely Cause
- Tumbles but no heat at all — heating element at $362, thermal fuse at $332, or cycling thermostat at $350. 969 company jobs at a $368 median. On electric dryers a tripped half of the double breaker gives the same symptom and costs nothing, so that gets checked first.
- Heats but clothes are still damp after a full cycle — airflow. A restricted vent, a lint-packed duct or a failing blower wheel at $368. Clearing the vent runs $350. See dryer not heating.
- Motor runs but the drum does not turn — drive belt at $322 or the idler pulley. 223 company jobs logged as not tumbling at a $335 median, and one of the most common single repairs we do.
- Squealing or rumbling as it turns — drum rollers or idler pulley at $349. Noise jobs run $349 across 601 of them. Left alone the rollers eventually seize and take the belt with them.
- Will not start at all — door switch at $321, thermal fuse at $332, or the start switch. 151 company jobs at $341. A door that is not latching fully produces this and costs nothing to correct.
- Starts then shuts off part-way through — high-limit thermostat responding to restricted airflow, or a failing motor at $394. 34 company jobs at $368. Almost always worth looking at the vent before the motor.
- Takes two cycles to dry one load — this is a vent message, not a dryer message, and it is also a fire risk. Worth acting on rather than living with.
Which Dryer Brands We See in St. Johns
Only 5 of our St. Johns dryer jobs carry a brand, Whirlpool 3 and Samsung 2, which is far too small to say anything about this ZIP and we are not going to try. For context our company-wide dryer mix across 2,524 tagged jobs runs Samsung 25.8 percent, Whirlpool 19.3 percent, GE 17.4 percent, Maytag 12.1 percent and LG 11.3 percent.
The practical point holds regardless of brand: belts, rollers, thermal fuses, thermostats and elements for the mainstream platforms ride on the van, and they are the overwhelming majority of dryer repairs, which is why most dryer jobs finish in a single visit. Control boards at $478 are the main exception and are more likely to need ordering.
As always this counts calls, not reliability. See most reliable appliance brands and appliance repair cost by brand.
Repair or Replace, in St. Johns Numbers
A dryer repair with a part replaced runs a $352 median across our whole book against roughly $650 to $1,100 for a mid-market replacement delivered and installed, so a single repair is comfortably under half the cost of replacing.
The decision is more clear-cut on a dryer than on anything else in the house for one reason: with a part-fitted share of 79.5 percent company-wide, when we come out there is usually a defined failed part with a defined price, not an open-ended investigation.
The one line that changes the calculation is the control board at $478 on an older machine, which is the point at which a second repair starts competing with a new appliance. Two local notes. A stacked washer-dryer column carries a $150 diagnostic rather than $99, because both units have to be separated before anything can be seen, and on a stacked pair a replacement decision usually covers both machines.
And whichever way you go, deal with the vent run: a new dryer on a restricted duct will not dry any better than the old one did. Framework in the repair or replace guide, service life in how long dryers last.
Discounts Applied Automatically
Priority Membership
$179 a year — five diagnostics, priority slots
- Five free diagnostic visits a year, a $495 value
- Priority scheduling with 24 to 48 hour response
- $30 off labor on every repair
- Extended warranty on all Bozmanfix work
What Jacksonville Customers Say About Bozmanfix
“My dryer quit working last week. They got me scheduled very quickly, came out on time and fixed the problem within 30 minutes. I always love using them.”
“Dmitriy did efficient and effective work for my dryer that had a busted component. Showed me the breaks specifically and explained the repairs well. Happy and would use again.”
“Was having dryer problems. Chris was great. Very efficient, was in and out in 15 minutes, super easy. Highly recommend.”
“They were very quick and prompt with showing up to take care of our dryer on a Saturday afternoon. Thank you.”
Dryer Repair in St. Johns — Questions We Get
How much does dryer repair cost in St. Johns, FL?
Our St. Johns dryer sample is small, six jobs with a part replaced, so the figures we stand behind are company-wide, from 4,218 completed dryer repairs: a median of $352 with a part replaced.
By component, a door switch $321, a drive belt $322, a thermal fuse $332, drum rollers $349, a cycling thermostat $350, a blocked vent cleared $350, a heating element $362, a blower wheel $368, a drive motor $394 and a control board $478.
All are parts, labor and the service call together. A diagnostic visit on its own is $99, or $150 on a stacked washer-dryer.
Why does this page use company-wide prices instead of St. Johns prices?
Because we only have 11 dryer jobs in ZIP 32259, seven of them paid and six with a part replaced, and 9 of the 11 fall in the last twelve months. That is not enough to publish an honest local component breakdown, so we have not invented one.
The local median is shown in the table with its job count attached so you can see exactly how much weight it carries, and every other line comes from thousands of repairs. When the local pool is large enough to say something specific, we will publish that instead.
My dryer heats but the clothes are still damp. What is wrong?
Almost always airflow rather than heat. A restricted or lint-packed vent duct, a crushed flexible transition hose behind the machine, a blocked exterior flap, or a failing blower wheel at $368.
Clearing a blocked vent runs a $350 median across 43 company jobs. If a load takes two cycles to dry, that is a vent message and also a fire risk, so it is worth acting on rather than living with.
Newer interior laundry rooms tend to have longer duct runs with more elbows, which makes this more likely, not less.
Is it worth clearing the vent when you replace the heating element?
Yes, and we check it in the same visit as a matter of course. A restricted vent is the most common reason an element burns out: trapped heat drives the element and the high-limit thermostat past what they are designed for.
The two jobs cost almost the same, $350 to clear a vent against $362 for an element, and replacing the element while leaving the restriction in place means you buy the same repair again later. That is the single most useful thing on this page.
How often does a dryer call end with a part fitted?
More often than any other appliance we service. Company-wide the dryer part-fitted share is 79.5 percent, against 59.0 percent on washers, 59.3 percent on dishwashers and 56.1 percent on freezers. In St. Johns the local figure is 6 of 7 paid visits, 85.7 percent.
In plain terms, a dryer that has stopped working usually has a genuinely failed part in it, which is why the $99 diagnostic being credited against the repair matters more on a dryer than anywhere else.
Do you work on gas dryers as well as electric?
Yes, both. We do not publish separate medians for gas-specific components such as igniters and gas valve coils, because our sample of those particular replacements is too small to be meaningful and we would rather say that than print a number we cannot stand behind.
If you can smell gas, do not run the machine or operate light switches. Leave the house and call your gas utility first, and we will look at the appliance once the supply has been made safe.
Do you work on stacked washer-dryer units?
Yes. The diagnostic on a stacked column is $150 rather than $99, because the two units have to be separated and pulled before anything can be inspected. As with the standard diagnostic, the $150 is credited against the repair when you approve the work. Stacked pairs also change the repair-or-replace maths, since a replacement decision normally covers both machines rather than one.
Do you cover Fruit Cove and Julington Creek as well as St. Johns?
Yes, all of it, at the same price. Fruit Cove, Julington Creek, Switzerland, Saint Johns and Jacksonville are all names USPS accepts for the same delivery area, ZIP 32259. Our dryer records inside that ZIP read 8 jobs written as Saint Johns, 2 as Jacksonville and 1 as Fruit Cove. There is no travel surcharge between the names and no difference in the price list.
Appliance Repair Services in St. Johns, FL
Six service pages for ZIP 32259, each built on the jobs we have actually run here.
Appliance Repair in St. Johns, FL — the full ZIP 32259 picture Serving St. Johns, FL and the wider Jacksonville area → View our full service areaBook Dryer Repair in St. Johns
Only 85.7 percent of our dryer visits here end with a part fitted. $99 diagnostic applied to the repair, $150 on a stacked pair, 90-day parts and labor warranty.