Dryer Repair in Orange Park FL

🔧 13 Orange Park Dryer Jobs 🎯 10 of 11 Visits Find a Real Failed Part 💰 $352 Local · $352 Company · Identical 🏷️ Eight Different Brands in Eleven Jobs 🛡️ 90-Day Parts and Labor Warranty

Dryer repair in Orange Park, FL runs a median of $352 once a part is replaced — which is the company median across 4,218 dryer repairs, to the dollar. That comes from 13 dryer jobs inside ZIP 32073, 11 paid and 10 with a component replaced.

Two numbers make this the most dependable page in the cluster. The local figure and the national one landing on the same dollar is not something you can arrange; it happens when a local sample is behaving normally.

And only one of eleven paid visits ended with no part to fit — a 90.9 percent part-fitted share, the lowest of any appliance in any area we publish, against 20.5 percent company-wide and 44.4 percent on washers in this same postcode. If your Orange Park dryer has stopped, it is broken.

Dryer Repair in Orange Park, FL 32073

12 of our 13 Orange Park dryer jobs are from the last twelve months. Elements, belts, rollers and switches for the mainstream platforms ride on the van, so most of these finish on the first visit.

Orange Park, Oakleaf or Fleming Island? Check Your ZIP

Three separate places in Clay County share Orange Park as a postal name. This page is ZIP 32073, the incorporated town. If your ZIP is 32065 that is Oakleaf, where the Census counts 31,034 people under the name Oakleaf Plantation even though USPS does not recognise it — see dryer repair in Oakleaf.

If your ZIP is 32003 that is Fleming Island, which accepts three city names at once, and where the dryer story is entirely different: see dryer repair on Fleming Island. Same price list and no travel surcharge between them, but with a part replaced dryers run $352 here, $369 in Oakleaf and $385 on Fleming Island.

What Dryer Repair Costs in Orange Park, by Component

Every figure below is the part, the labour and the service call together — the number that lands on your invoice. Price guides quoting the component alone will tell you a thermal fuse is fifteen dollars and then the bill arrives at $332.

The component rows are company-wide, since ten local jobs cannot be split across ten named repairs; the last two rows are the totals, and here they agree exactly.

RepairMedian, full ticketSourceJobs (n)
Door switch$321Company-wide54
Drive belt$322Company-wide259
Thermal fuse$332Company-wide84
Drum rollers or idler pulley$349Company-wide218
Thermostat$350Company-wide144
Blocked vent cleared$350Company-wide43
Heating element$362Company-wide360
Blower wheel$368Company-wide22
Drive motor$394Company-wide55
Control board$478Company-wide71
All dryer jobs with a part replaced$352 · middle half $294 to $437Company-wide4,218
All dryer jobs with a part replaced$352 · middle half $305 to $375Orange Park 3207310
💡 The medians match to the dollar and the local band is tighter — $305 to $375 against $294 to $437. Ten Orange Park dryer repairs sit inside a $70 window. That is what it looks like when a category is behaving predictably rather than being pulled around by one big invoice, and it is why we will quote a realistic dryer range over the phone and will not do the same for a refrigerator.

Our local jobs bear it out. Nine of the ten component repairs run between $295 and $400: $400, $375, $375, $355, $349, $335, $305, $298, $295. Only one sits outside, a Kenmore at $519, which is control-board territory. There is no cheap tail and no expensive tail — just the mid-priced mechanical work that a dryer generates when it fails: an element, a belt, rollers, a thermostat, a switch.

Why Orange Park Dryers Fail the Way They Do

A dryer either heats or it does not, tumbles or it does not, and behind either symptom there is nearly always a failed element, fuse, belt, roller, thermostat or motor. There is very little in a dryer that can look broken while being fine — which is exactly why the part-fitted share of 90.9 percent while washers in the same postcode run 44.4 percent.

The one genuine exception is airflow: a dryer whose exhaust duct has silted up will run, tumble and heat while drying nothing, and it will slowly cook its own thermostats and element in the process. That is the check worth doing when you book, and it is free.

the lowest part-fitted share on any page we publish 10 OF 11 PAID VISITS

9.1 percent, against a company-wide dryer figure of 20.5 percent that is already the lowest of any appliance we service. Inside this same ZIP, refrigerators sit close to even and washers 44.4 percent.

Eleven visits is a modest sample and one job either way moves it by nine points, so treat the precise figure lightly — but the direction is consistent with every dryer sample we hold: Oakleaf runs 1 of 10, Middleburg 2 of 10, Fleming Island 3 of 10. A dryer complaint is the most likely of any appliance call to end in an actual repair.

Clearing a vent costs the same as the element it destroyed $350 AGAINST $362

This is the most useful line on the page. A blocked exhaust duct is the most common reason a heating element burns out, and clearing one runs $350 company-wide against $362 for a new element.

Development-built and older single-family housing alike tends to run the duct through a wall cavity, an attic or under a floor to reach outside, so the run is long, has several elbows and has usually not been opened since the house was finished.

Add north Florida humidity — the air being pushed through is already damp — and lint mats into a felt-like layer rather than staying loose. The cheap version of this repair is the one you do before the element fails.

Eight different brands in eleven branded jobs INCLUDING ROPER AND AMANA

Samsung 3, Whirlpool 2, and one each of Kenmore, Maytag, LG, GE, Amana and Roper. That is the most fragmented brand picture of any appliance in this ZIP — compare refrigerators here, where Frigidaire alone is 9 of 19. Roper and Amana are legacy budget names you do not see in new kitchens, which tells you the laundry rooms of Orange Park hold machines of quite different vintages.

Practically it is good news: elements, belts, rollers, thermal fuses and door switches are broadly interchangeable in availability terms across mainstream platforms, so these repairs still finish in one visit. A brand table records how often we are called out, not reliability.

On gas dryers we will not publish a component price TOO FEW JOBS COMPANY-WIDE

Gas dryers exist here and we service them. But across our entire company book, gas dryer igniters and valve coils appear fewer than ten times each — not enough to build a price line on, and we are not going to invent one to fill a gap in a table.

What we can tell you is the shape of the job: on a gas dryer, no-heat is usually the igniter, the flame sensor or the valve coils, all sitting in the burner tube at the bottom front of the machine, and all diagnosed on the same $99 visit as an electric fault. You get the total before we start either way.

Two checks, and the first is the whole point. Run the dryer for two minutes and hold your hand over the outside vent flap. Strong warm airflow means the duct is clear and the fault is electrical — element, fuse or thermostat. Weak or no airflow means the duct is the problem, and everything you are about to pay for sits downstream of it. Second, look inside the lint filter housing, not just at the screen; a compacted layer below the filter restricts airflow exactly like a blocked duct. A blocked vent is a fire risk as well as a repair bill, which is why we treat it as the first question on a no-heat call rather than as an extra at the end.

Ten of our eleven paid Orange Park dryer visits ended with a real part replaced. Plan on $305 to $375, and expect it to finish in one visit. Book online or call (954) 902-6229.

Match Your Symptom to the Likely Cause

  • Tumbles but clothes come out damp — heating element at $362, or a vent run that has silted up at $350. Company-wide this symptom is 226 repairs at a $365 median. Check the outside vent flap first; it decides which of the two you are buying.
  • No heat at all — element, thermal fuse at $332, or a thermostat at $350. Our largest dryer symptom company-wide at 969 repairs, median $368. On a gas machine it is the igniter or valve coils instead. See dryer not heating.
  • Runs then shuts off partway through the cycle — a thermostat cutting out on high temperature, which nearly always means restricted airflow rather than a failed part. Act on this quickly, because the same heat is working on the element.
  • Loud rumbling or squealing — drum rollers or the idler pulley at $349, or the blower wheel at $368. Noise is our biggest dryer category company-wide at 601 repairs.
  • Motor runs but the drum does not turn — drive belt at $322, one of the cheapest lines on the table and a same-visit repair on almost every platform.
  • Completely dead, no lights, no response — door switch at $321, thermal fuse, or a control board at $478. Our one outlying local job at $519 was in that territory.

Where in Orange Park We See This Work

All 13 dryer jobs are inside ZIP 32073, with 12 of them in the last twelve months — the most current sample in this cluster. One price across the whole ZIP with no travel surcharge.

If your dryer is stacked with the washer the diagnostic is $150 rather than $99, because the pair has to be pulled and separated before either can be assessed; the same applies to a double wall oven.

See also the Orange Park washer page, where the picture is the exact opposite — 55.6 percent of visits end with a part fitted. Neighbouring Clay County coverage: Oakleaf in 32065, Fleming Island in 32003, Middleburg in 32068 and Green Cove Springs in 32043. Full structure on the Jacksonville locations hub.

Repair or Replace, in Orange Park Numbers

A dryer repair with a part replaced runs $352 here, against roughly $650 to $1,100 for a mid-market replacement installed.

That is the widest repair-to-replace margin of any appliance we service, and it explains why dryers carry the most straightforward call in our entire company book — only 20.5 percent of households who receive a dryer diagnosis turn the repair down, against 41 percent on washers and 44 percent on freezers.

A dryer is mechanically simple and long-lived, and a $352 repair on a sound drum and motor is good value.

Two cases deserve a second thought: a control board at $478 on a machine past ten years, and a second heating element on a dryer whose vent was never dealt with — there the honest fix is the duct, because a new dryer on the same duct will follow the old one.

Expected life is in how long dryers last, framework in the repair or replace guide.

Discounts Applied Automatically

$30 OFFVeteransEvery repair
$30 OFFSeniorsEvery repair
$20 OFFNew CustomersFirst repair

Priority Membership

$179 a year — five diagnostics, priority slots

  • Five free diagnostic visits a year, a $495 value
  • Priority scheduling with 24 to 48 hour response
  • $30 off labor on every repair
  • Extended warranty on all Bozmanfix work

What Jacksonville Area Customers Say About Bozmanfix

★★★★★

“Dmitriy did efficient and effective work for my dryer that had a busted component. Showed me the breaks specifically and explained the repairs well. Happy and would use again.”

— Nathaniel Wiest · Verified Google review
★★★★★

“Vladimir did an amazing job, he was very fast and professional. My dryer works great.”

— CB Utilities · Verified Google review
★★★★★

“Was having dryer problems. Chris was great. Very efficient, was in and out in 15 minutes, super easy. Highly recommend.”

— Wilhelmina Krekel · Verified Google review
★★★★★

“My dryer quit working last week. They got me scheduled very quickly, came out on time and fixed the problem within 30 minutes. I always love using them.”

— Courtney Nicodemus · Verified Google review

Dryer Repair in Orange Park — Questions We Get

How much does dryer repair cost in Orange Park, FL?

The median is $352 once a part is replaced, parts and labor and the service call together, with the middle half of local jobs between $305 and $375. That comes from 10 component replacements out of 11 paid dryer visits inside ZIP 32073, and it matches the company-wide median of $352 across 4,218 repairs exactly.

By component, company-wide: door switch $321, drive belt $322, thermal fuse $332, drum rollers $349, thermostat $350, blocked vent cleared $350, heating element $362, blower wheel $368, drive motor $394, control board $478.

Why is the dryer the most reliable price on this cluster?

Because the local figure and the national one agree to the dollar, and because ten local repairs sit inside a $70 window against a $143 company window. Nine of our ten component jobs run between $295 and $400, with only one outlier at $519 in control-board territory.

There is no cheap tail and no expensive tail — just the mid-priced mechanical work a dryer generates when it fails. That predictability is why we will give a realistic dryer range over the phone and will not do the same for a refrigerator.

What does the $99 diagnostic cover?

The technician tests the appliance, identifies the fault, and gives you a firm total before any work starts. When a part is needed the $99 comes off the repair, and every completed repair carries a 90-day parts and labor warranty.

When the fix turns out to be a setting, a filter or something that can safely wait, you pay the diagnostic only and get told exactly what to watch for. Either way you know the number before anything is spent.

My dryer runs but the clothes are still damp. What is it?

Either the heat has failed or the air is not moving, and you can tell which for nothing. Run the machine two minutes and hold your hand over the outside vent flap. Strong warm airflow means the duct is clear and the fault is the element at $362, a thermal fuse at $332 or a thermostat at $350.

Weak airflow means the duct is the problem and clearing it is $350. Getting that order right is the difference between fixing the cause and paying for the same part twice, because a blocked vent is the most common reason an element fails.

Do you clean dryer vents in Orange Park?

Yes. Company-wide a cleared blocked vent runs $350 across 43 jobs, essentially the same money as a new heating element at $362. Housing here typically runs the exhaust duct through a wall cavity, an attic or under a floor to reach outside, so the run is long, has several elbows and has usually not been opened since the house was built.

North Florida humidity means the air being pushed through is already damp, so lint mats rather than staying loose. A blocked duct is a fire risk as well as a repair bill, which is why we treat it as the first question on a no-heat call.

Which dryer brands do you see in Orange Park?

Eleven of our 13 local dryer jobs carry a brand and there are eight different ones among them: Samsung 3, Whirlpool 2, and one each of Kenmore, Maytag, LG, GE, Amana and Roper. That is the most fragmented brand picture of any appliance in this ZIP — compare refrigerators here, where Frigidaire alone is 9 of 19.

Roper and Amana are legacy budget names, which tells you these laundry rooms hold machines of quite different vintages. Elements, belts, rollers and fuses are broadly available across mainstream platforms, so repairs still finish in one visit.

Do you work on gas dryers, and what do they cost?

We do, but we will not publish a component price for them. Across our entire company book gas dryer igniters and valve coils appear fewer than ten times each, and a price line built on that is not data.

The job shape is this: no-heat on a gas dryer is usually the igniter, the flame sensor or the valve coils, all in the burner tube at the bottom front of the machine, and all diagnosed on the same $99 visit as an electric fault. If your gas comes from a tank rather than a meter, mention it at booking.

Is it worth repairing, or should I replace it?

At $352 median with a part replaced against roughly $650 to $1,100 for a mid-market replacement installed, repair wins comfortably on any dryer with a sound drum and motor — which is why 20.5 percent of households company-wide go ahead with a dryer repair, the highest rate of any appliance.

The cases that turn are a control board at $478 on a machine past ten years, and a second heating element on a dryer whose vent was never cleared. In that second case the honest answer is to fix the duct first, because a new dryer on the same duct will go the same way.


Book Dryer Repair in Orange Park, FL

13 dryer jobs on record in ZIP 32073, 12 of them in the last twelve months. $99 diagnostic applied to the repair and $150 on a stacked pair, 90-day parts and labor warranty.

Book online Call us
Book online Call us