Dryer Repair Jonesboro GA

🔥 24 Jonesboro Dryer Jobs 📍 30236 · 30238 🏠 21 Jonesboro Households 💰 $99 Diagnostic · Applied to the Repair 🛡️ 90-Day Parts and Labor Warranty
Written by Bozmanfix TeamReviewed by Eugen, Appliance Repair Technician, 5+ yearsUpdated October 2026

Dryer repair in Jonesboro, GA has a median cost of $334 in Bozmanfix records once a part is replaced. Those two figures are closer together than on any other appliance in this city, and there is a reason.

A dryer is an honest machine: if it has stopped heating or stopped turning, something in it has failed, and there is very little in between.

The file is new: 24 jobs, and the first of them in 2025. Our kitchen work in Jonesboro goes back years, and the laundry rooms followed.

Below is what that file actually contains, invoice by invoice, alongside company-wide component pricing from 4,559 completed dryer jobs.

Dryer Repair in Jonesboro, GA

No heat, damp clothes after a full cycle, will not tumble, will not start, shutting off part way, burning smell. Electric and gas, freestanding and stacked. Both Jonesboro ZIP codes, total confirmed before the work starts.

What a Dryer Repair Costs, by the Part That Failed

This table is company-wide, from 4,559 completed dryer jobs, so every part has a price built on real volume. Every figure is the full ticket: the part, the labor and the service call added together. Gas igniters and gas valve coils are priced on the visit, with the total confirmed before work starts.

What failedMedian totalJobs (n)
Door switch$32454
Drive belt$322259
Thermal fuse$33284
Drum rollers or idler pulley$350218
Cycling thermostat$349144
Blocked vent cleared$35743
Heating element$367360
Blower wheel$37222
Drive motor$39455
Control board$50721
💡 Look at the vent line. Clearing a blocked vent costs $357 and replacing a heating element costs $367 – ten dollars apart. That is not a coincidence, it is the same job seen from two ends, because a blocked vent is what cooks a heating element to death in the first place.

The Whole Jonesboro Dryer File, Named

Here is every Bozmanfix dryer invoice in Jonesboro that says what was actually done. A Samsung heating element replacement at $469. A dryer heating element at $350, part and labor written separately on a combined visit that also replaced washer struts.

Temperature sensors and fuses replaced at $305, on a job the technician recorded as reassembling the entire dryer back to how it was. A Whirlpool door lock replaced at $265. And the interior cabinet cleaned out of lint on a GE at $225, which is the cheapest thing on this list and quite possibly the one that saved an element.

The other local repairs run from $265 to $650 – they are inside every median on this page.

The two largest tickets in the file are a $650 visit tagged for a washer and a dryer together, and an LG at $579 with no part named. Set against the Bozmanfix company-wide table above, the named five land where you would expect: an element at the top, a door switch and a lint clean-out at the bottom, and a sensor-and-fuse job in the middle.

Nothing in Jonesboro is priced unusually.

Why Jonesboro Dryers Fail the Way They Do

The vent is the cause and the heat is the symptom $225 · $357 · $367

Almost every no-heat dryer we open has a restricted vent somewhere behind it, and in a city whose housing went up between 1960 and 1980 the vent run is the part nobody has looked at since the house was built.

A 1972 laundry room vents through an exterior wall or, worse, up through a crawl space or a soffit in flexible foil duct that has since sagged into a low point where lint settles.

Restricted airflow means the drum never reaches its shut-off temperature, so the cycling thermostat holds the element on far longer than it was designed for, and the element eventually opens. That is the whole mechanism, and it is why a Bozmanfix invoice on a GE for cleaning lint out of the interior cabinet, $225, is a cheaper version of the same story as a $469 element replacement.

If your dryer needs two cycles where it used to need one, the machine is telling you about the duct, not about itself. Book it while it is still a duct problem. The element itself is explained in dryer heating element replacement cost and the diagnosis in dryer not heating.

A dryer that has stopped is nearly always a failed part

A dryer that will not heat has a failed element, a blown thermal fuse, a bad thermostat or a blocked vent.

A dryer that will not turn has a belt, an idler or a motor. The list of things it can be is short and all of them are parts we carry. Practically that means the decision is simple: book it.

The file starts in 2025, so every number is current 0 BEFORE 2025

Fourteen Jonesboro dryer jobs in 2025, ten in the first seven and a half months of 2026, and none at all before that. Nineteen of the 24 fall inside the last twelve months. Our washer file here tells the same story one step ahead of it: 1 job in 2023, 10 in 2024, 31 in 2025 and 32 so far in 2026.

Read together, the two files say that Bozmanfix arrived in Jonesboro through its kitchens and has since moved into its laundry rooms. Every number on this page describes machines in service right now rather than a decade of averages, and every one of the 24 is from 2025 or 2026.

The component table above is drawn from 4,218 jobs, and the named invoices show the local work.

Stacked columns, and why the diagnostic is $150 5 INVOICES

Five of the Bozmanfix laundry invoices in Jonesboro are for stacked or combination washer-dryer units, and one of them, an LG stacked pair, came in at $320. A laundry alcove framed in 1972 for a side-by-side pair is now frequently filled by a stacked column, because that is what fits, and on those the diagnostic is $150 rather than $99.

The reason is mechanical: the column has to be unstacked or drawn out of its recess before the back of either machine can be reached, and on a combination unit the washer and the dryer share a cabinet, a drain and often a control board, so one is diagnosed through the other.

It also means the fault sometimes belongs to the other half – the single largest local Bozmanfix laundry ticket, $650, is one visit tagged for a washer and a dryer together. Say on the phone that yours is stacked, and the $150 is quoted before the visit rather than discovered at the door. It is applied to the repair exactly the way the $99 is.

LG and Whirlpool at the top, Samsung at the bottom $434 · $282

Our Jonesboro dryer brand tags run Whirlpool 7, GE 5, LG 4 and Samsung 4, with two Maytags. The two ends are worth naming.

The four Whirlpool repairs run a median of $434 and the four Samsung repairs a median of $282, which is a $152 gap on the same appliance in the same city, and the single largest completed Bozmanfix dryer invoice naming one machine is an LG at $579.

What matters more for your visit is which parts wait: Whirlpool, GE and Maytag dryer components ride on the van, and Samsung and LG components are the ones we normally order, so on those two the answer you want before approving anything is the lead time, and you will get it.

Context is on the most-serviced appliance brands.

Gas or electric, two different diagnoses ATLANTA GAS LIGHT

Jonesboro homes sit on the Atlanta Gas Light delivery network with a choice of competing marketers, and in housing of this age gas laundry connections are common. On an electric dryer the heat comes from a resistance element at $367 company-wide at Bozmanfix.

On a gas dryer it comes from an igniter, a flame sensor and a gas valve with two coils, and the diagnosis is a different sequence: the igniter glows, the sensor confirms, the coils open the valve, and a failure anywhere in that chain gives you a drum that turns for an hour with cold air in it.

On a gas machine the technician prices the exact igniter or valve coil on the visit and quotes the total before starting.

And a safety line that is not boilerplate: if you smell gas at the dryer, do not run it to test, leave the house and call the gas utility first and us second. Details in our gas appliance safety guide.

Three things to tell us when you book. First, how strong and hot the air feels at the outside vent while the dryer runs, and whether the duct behind it is flexible foil that sags anywhere on its run – that low point is where lint collects, and clearing it is part of the job. Second, whether the lint screen looks glazed; fabric-softener residue can choke airflow even when the screen looks clean. Third, if the drum will not turn at all but the motor hums, say so – that is a seized idler or a snapped belt rather than anything electrical, at the cheap end of the table above at $322 to $349.

🚚 Nineteen of our 24 Jonesboro dryer jobs are from the last twelve months, so this is a live route. Whirlpool, GE and Maytag parts ride on the van, which covers most of the work here.

Match Your Symptom to the Likely Cause

  • Runs a full cycle and the clothes are still damp – $375 by symptom across all Bozmanfix jobs, and the commonest cause is airflow rather than heat: a blocked vent cleared is $357, a blower wheel $372. Tell us at booking how the air feels at the outside vent.
  • Tumbles with no heat at all – $370 by symptom across all Bozmanfix jobs. On an electric machine the heating element at $367, the thermal fuse at $332 or the cycling thermostat at $349; one Jonesboro invoice is a Samsung element at $469 and another is temperature sensors and fuses at $305. A blown thermal fuse is almost always a symptom of the restricted vent that blew it, so replacing it without clearing the duct buys you a few months.
  • Will not tumble, or hums without turning – $341 by symptom across all Bozmanfix jobs: a drive belt at $322, drum rollers or the idler pulley at $350, or the drive motor at $394. A snapped belt is usually audible as a free-spinning drum you can turn by hand.
  • Will not start at all – $345 by symptom across all Bozmanfix jobs. The door switch at $324 is the first suspect and one of the cheapest, and one Jonesboro job was a Whirlpool door lock at $265. On a stacked pair the technician also checks whether the washer half is holding the interlock.
  • Starts and then shuts off part way through – $380 by symptom across all Bozmanfix jobs, and the machine is protecting itself: a thermal cut-out is opening because the cabinet is running hotter than it should, which is the vent again nine times in ten.
  • A burning or hot-fabric smell – stop using it. That is lint against a hot element or a hot bearing, and one of the local Bozmanfix jobs was exactly this, cleaning lint out of the interior cabinet of a GE at $225. It is the cheapest invoice in this file and the most valuable one.
  • New noise: thumping, squealing or grinding – $350 by symptom across all Bozmanfix jobs. Thumping with the drum is a flat spot on a roller, squealing that follows the drum speed is the idler, grinding is a bearing. Noise is decoded in what appliance noises mean.

The Two Jonesboro ZIP Codes

We cover 30236 and 30238 at one price list and no travel surcharge. On dryers the split is 13 Bozmanfix jobs in 30236 and 11 in 30238, with a $379 median on the north and east side and a $294 median on the west and south side.

Both ranges overlap heavily – $320 to $579 in one, $276 to $469 in the other.

What the ZIP split does show, and this holds across the whole cluster rather than just the dryer file, is that 30238 calls us more often relative to its housing: 12.7 jobs per thousand homes against 10.1 in 30236, in the ZIP with the lower median income and the higher share of owner-occupiers.

That is the third Georgia cluster in a row where call frequency tracks ownership rather than money. Same $99 diagnostic, same $150 on a stacked pair, same 90-day parts and labor warranty in both.

Repair or Replace, on the Jonesboro Numbers

The dryer is the easiest repair-or-replace call in the house, and Jonesboro does nothing to complicate it. At $334 with a part replaced, against a new dryer plus delivery, installation, a new duct connection and the disposal of the old machine, repair wins on anything that is not physically rusting apart.

The mechanical parts of a dryer are simple and cheap to reach, which is why nine of the ten rows in the table above sit between $321 and $394 – the exception is the control board at $507, and even that is a single afternoon.

There is one honest caveat and it is not about money. If the machine is more than fifteen years old and the fault is the drum bearing or the cabinet itself rather than a component bolted to it, the labor to reach it starts to look like the price of a new machine, and you hear the full price before any work starts.

Service lives are in how long dryers last, the arithmetic in the repair versus replacement guide and appliance repair approval rate.

Three dryer situations we treat as urgent rather than routine. A burning smell, scorch marks on the clothes or heat coming off the cabinet means lint against something hot, and the machine should be unplugged and left alone rather than run one more load to see. A dryer that trips its breaker every time it is reset is a shorted element or a damaged wiring harness, and repeated resets on a marginal circuit are how a fault becomes a fire. And on a gas dryer, if you smell gas do not press start to test the igniter and do not flip a light switch: leave the house, call the gas utility first and us second. Jonesboro homes are on the Atlanta Gas Light network with competing marketers, and the utility handles the line while we handle the appliance. Details in our gas appliance safety guide.
What you pay and when The diagnostic is $99, or $150 on a stacked washer-dryer or a combination unit, because the column has to come apart before the back of either machine can be reached. The fee is applied to the repair the moment you approve the work, so an approved job never charges you twice. You get the total before the technician starts, including the lead time on any Samsung or LG part that has to be ordered. Every completed repair carries a 90-day parts and labor warranty. If the machine does not need a part you pay the diagnostic and nothing else. Book online or call (470) 777-7697.

Discounts Applied Automatically

$30 OFFVeteransEvery repair
$30 OFFSeniorsEvery repair
$20 OFFNew CustomersFirst repair

Priority Membership

$179 a year – five diagnostics, priority slots

  • Five free diagnostic visits a year, a $495 value
  • Priority scheduling with 24 to 48 hour response
  • $30 off labor on every repair
  • Extended warranty on all Bozmanfix work

What Atlanta Customers Say About Bozmanfix

★★★★★

“Alex was the best. Fixed my machine with a couple of days! Soo happy!!”

– Iysha Q. · Verified Bozmanfix customer
★★★★★

“Technician arrived right on time, diagnosed the problem with my dryer within a few minutes and had the machine working again within a half hour. Good people. Family owned business. Would recommend them and I will use them again.”

– Dan C. · Verified Bozmanfix customer
★★★★★

“My dryer started making a lot of noise. Vadym was awesome I needed new rollers. He came back within a few hours with a roller kit. A few minutes after, I had a purring dryer. He was friendly and considerate”

– Brenda M. · Verified Bozmanfix customer
★★★★★

“Thank you so much! Excellent and I appreciate you coming out and fixing the issue with our dryer. Will definitely use you again”

– Emily R. · Verified Bozmanfix customer

Dryer Repair in Jonesboro – Questions We Get

How much does dryer repair cost in Jonesboro, GA?

The Bozmanfix median is $334 once a part is replaced, from 18 paid dryer jobs inside the two Jonesboro ZIP codes. The middle half of with-a-part jobs runs $276 to $469.

The component figures below are company-wide from 4,559 completed Bozmanfix dryer jobs and include the part, the labor and the service call together: door switch $324, drive belt $322, thermal fuse $332, drum rollers or idler $350, cycling thermostat $349, blocked vent cleared $357, heating element $367, blower wheel $372, drive motor $394, control board $507.

How long have you repaired dryers in Jonesboro?

Since 2025. Our route reached Jonesboro through its kitchens: the refrigerator file here goes back to 2023 and has run steadily at 20 to 28 jobs a year, while the dryer file is 14 jobs in 2025 and 10 in the first seven and a half months of 2026.

Every local Bozmanfix invoice that names what was done is published: a Samsung heating element at $469, a dryer heating element at $350, temperature sensors and fuses at $305, a Whirlpool door lock at $265 and a GE cabinet cleaned out of lint at $225.

My dryer takes two cycles to dry a load. Is that the heating element?

More often it is the airflow. A dryer that heats but dries slowly almost always has restricted airflow rather than a failed element, because a dryer removes water by moving hot air through the drum and out of the house.

Tell us at booking how strong the air feels at the outside vent, so the technician arrives ready to clear the duct as well as test the element.

Clearing a blocked vent is a $357 job company-wide at Bozmanfix, ten dollars less than replacing a heating element, and it is worth doing before the element fails rather than after, because a restricted vent is what cooks elements and blows thermal fuses in the first place.

Why is the diagnostic $150 on my stacked unit?

Because a stacked pair or a combination washer-dryer has to be unstacked or drawn out of its recess before the back of either machine can be reached, and on a combination unit the two halves share a cabinet, a drain and often a control board, so one is diagnosed through the other.

Five of the Bozmanfix laundry invoices in Jonesboro are stacked or combination units, which follows from laundry alcoves framed in the 1960s and 1970s for a side-by-side pair and now filled by a column. The $150 is quoted when you book rather than discovered at the door, and it is applied to the repair exactly the way the $99 is.

Do you repair gas dryers, and what does that cost?

Yes. Jonesboro homes are on the Atlanta Gas Light delivery network with a choice of marketers, and gas laundry connections are common in housing of this age.

The technician prices the exact igniter or valve coil on site, and you get the total before any work starts.

The diagnosis on a gas machine is a chain rather than a single part: the igniter glows, the flame sensor confirms, the valve coils open, and a break anywhere gives you a drum that turns for an hour with cold air in it. If you smell gas, do not run the machine to test it. Leave the house and call the gas utility first.

What does the $99 diagnostic include?

A meter on the machine and a firm total before any work starts. The technician tests the actual fault rather than guessing from the symptom, so the part that goes in is the part that failed.

The diagnostic is $99, or $150 where a machine has to be unstacked or drawn out of a cabinet before it can be opened, and it is applied to the repair the moment you approve the work, which means an approved job never pays it twice.

You also get the lead time up front on any part that has to be ordered, and every completed repair carries a 90-day parts and labor warranty. In Jonesboro the Bozmanfix median repair once a part is replaced is $334, so you have a good idea of the number before anyone arrives.

Is it worth repairing a dryer at all, or should I replace it?

Repair, in almost every case. At the Jonesboro median of $334, against a new dryer plus delivery, installation, a fresh duct connection and disposal of the old one, the arithmetic is not close, and the mechanical parts of a dryer are simple and cheap to reach: nine of the ten common failures sit between $321 and $394 company-wide at Bozmanfix.

The exception is a machine over fifteen years old with a drum bearing or cabinet fault rather than a bolt-on component, where the labor to reach it approaches the price of a new machine. We will tell you when you are there rather than quote it.


Book Dryer Repair in Jonesboro

24 Bozmanfix dryer jobs on record in this city, 19 of them in the last twelve months. $99 diagnostic applied to the repair, $150 on a stacked pair, 90-day parts and labor warranty.

Book online Call us(470) 777-7697