Dryer Repair in Clearwater, FL
Bozmanfix has 32 paid Clearwater dryer jobs on record, priced from real invoices.
The Bozmanfix median is $357 once a part is replaced and $352 across all paid visits. If your dryer has stopped here, book it. Company-wide prices by part, built from Bozmanfix invoices, are on our appliance repair parts cost page.
Dryer Repair in Clearwater, FL
Electric and gas, vented and stacked, all nine Clearwater ZIP codes in Pinellas County at one price. 25 of these jobs are from the last twelve months.
A Five Dollar Gap, and What It Means
Every appliance has two medians: what a typical visit costs across everything we did, and what it costs once a component genuinely goes in. The distance between them comes from the mix of work rather than from the price of any single repair. On the Clearwater dryer that distance essentially disappears.
| Dryer, by city | With a part | Paid (n) |
|---|---|---|
| Clearwater | $357 | 32 |
| St. Petersburg | $367 | 67 |
| Riverview | $341 | 31 |
| Lakeland | $317 | 36 |
| Bradenton | $298 | 50 |
The reason is mechanical rather than local. A dryer either turns and heats, or it does not. There is no load-balance system to trip, no drain path to block, no pair of water supplies to half-close, no control board deciding a suds condition means it should refuse to run.
A dryer has a motor, a belt, rollers, a heating circuit and a thermal cut-out, and when one of them fails the machine stops in a way you cannot mistake for anything else.
What the Individual Repairs Cost
Across 29 Clearwater dryer jobs with a part, the median is $357.
One local figure deserves a note: the middle half of Clearwater dryer repairs runs $326 to $470, and that upper bound is the highest of the five cities – Bradenton stops at $395 and Riverview at $375.
It is consistent with control boards at $507 appearing more often here than a belt or a door switch, which fits a city with more electronic and stacked machines.
The full picture is in appliance repair cost for 59 components.
What We Actually See in Clearwater
GE runs the laundry here GE 32 · SAMSUNG 23 · WHIRLPOOL 18 PERCENT
Of 22 branded Clearwater dryer jobs, GE is 32 percent, Samsung 23, Whirlpool 18, Kenmore 9 and LG 9. That is a different shape from the washers in the same houses, where no brand exceeds 21 percent – dryers get replaced independently of washers more often than people assume, and a failed dryer tends to be swapped for whatever was available that week.
Kenmore at 9 percent is worth noting: Kenmore has not been a going concern as a brand for years, so a Kenmore dryer on our schedule is by definition an older machine, and laundry rooms are where old machines survive longest.
GE, Whirlpool and Maytag dryer parts – belts, rollers, switches, thermostats, elements – ride on the van.
The mainland ZIPs lead our Clearwater dryer work7 OF 32 PAID JOBS
Our paid Clearwater dryer work sits at 7 jobs in 33761, then 4 each in 33764 and 33755. That differs from our refrigerator distribution, which piles into 33767 on the barrier island. The reason is straightforward: beachfront condominiums frequently have compact, stacked or shared laundry rather than a full-size standalone dryer, so the barrier island generates refrigerator work far out of proportion to its population but not dryer work.
33761 and 33764 are mainland single-family territory where every household has its own machine. All nine ZIP codes get the same price and the same $99 diagnostic; the full table is on the Clearwater hub page.
Airflow is the fault that disguises itself as a heating fault
A dryer that runs a full cycle and leaves clothes damp feels like a heating problem, and most people have decided that before they call. Often it is a vent run that has silted up, strangling airflow so the machine cannot carry moisture out of the drum.
It is also the one dryer fault with a safety dimension attached, because lint trapped against a heat source is how dryer fires start.
We published dryer fire statistics for that reason: 13,820 US home fires a year involve a dryer, and across 2,277 of our own service visits almost nobody calls us about the vent until something else fails first.
The dryer is the appliance where waiting reliably costs money
There is a practical reason not to sit on a dryer fault. A washer with an unbalanced load is annoying and stays annoying. A dryer running on failed rollers lets the drum sit unsupported, which then wears the rear bearing and the seal behind it and turns a repair into a considerably larger one.
A dryer with restricted airflow keeps tripping its thermal cut-out, which shortens the life of the element that cut-out is protecting. And a dryer with a silted vent is accumulating lint against a heat source. Of all the appliances in your house, this is the one where the cost of a month’s delay is most predictable.
Match Your Symptom to the Likely Cause
- Drum will not turn, motor hums – drive belt. A snapped belt is usually audible as a thump for a week beforehand.
- Loud rumble or a squeal that rises with the drum – drum rollers or the idler pulley. Do not run it long in that state; an unsupported drum wears the rear bearing and the seal behind it.
- Runs a full cycle, clothes still damp – airflow before anything else: lint screen, the duct behind the machine, then the vent run to the wall or through the building. If airflow is genuinely strong, it is the thermostat or the element.
- No heat at all – thermal fuse, thermostat, or the heating element on electric machines; igniter or coils on gas.
- Will not start, dead when the door closes – door switch, one of the two cheapest common dryer repairs there is.
- Shuts off partway through a cycle – usually a thermal cut-out doing its job because airflow is restricted. That points back at the vent rather than at a broken part.
Repair or Replace, in Clearwater Numbers
A dryer repair with a part replaced runs $357 here against roughly $650 to $1,100 for a mid-market replacement installed, and considerably more for a stacked or compact unit of the kind common in Clearwater condominium laundry rooms.
That is better than two to one, and it holds up longer than most because the parts that dominate dryer work – belts, rollers, switches, thermostats, fuses – are wear items rather than end-of-life failures.
Replacing a belt on a ten-year-old dryer genuinely returns the machine to service rather than postponing the next failure by six months. The case for replacing is narrow: a control board on an old machine, or a drum whose rear bearing and seal have already been chewed up by running on failed rollers.
Expected service life is in how long dryers last, and the framework is the repair or replace guide.
Discounts Applied Automatically
Priority Membership
$179 a year – five diagnostics, priority slots
- Five free diagnostic visits a year, a $495 value
- Priority scheduling with 24 to 48 hour response
- $30 off labor on every repair
- Extended warranty on all Bozmanfix work
What Customers Say
“Even though my dryer could not be repaired during the visit because the part was not available, I was very impressed with Max. He was professional, friendly, and took the time to thoroughly diagnose the problem.”
“Max was very efficient and helpful in helping me decide what to do, and I really appreciate him showing up early so things could be fixed.”
“Vidaly was great! On time and got the job done quickly and efficiently.”
Dryer Repair in Clearwater – Questions We Get
How much does dryer repair cost in Clearwater, FL?
In Bozmanfix records, parts and labor and the service call together. Across all paid dryer visits the median is $352 and the base is 32 paid dryer jobs inside Clearwater.
What does the Clearwater dryer diagnostic include?
A measured diagnosis and a firm price before any work starts.
A dryer either turns and heats or it does not: there is no load-balance system, drain path or pair of water supplies to produce a false alarm.
My dryer runs but the clothes are still damp. Is the heater dead?
Airflow comes first. Weak airflow at the outside vent hood or a flap that barely moves means a restricted duct rather than a failed element, and clearing it may be the entire repair.
On the Gulf coast the exterior hoods also corrode and stick shut, which produces the identical symptom, and in a condominium the vent run may be long or shared, which makes the check more useful rather than less.
Is a noisy dryer urgent?
More than most faults, yes. A rumble or squeal that rises and falls with the drum is normally the rollers or the idler pulley. Running it in that state lets the drum sit unsupported, which wears the rear bearing and the seal behind it and turns a modest repair into a considerably larger one.
Of all the appliances in your house, the dryer is the one where the cost of a month’s delay is most predictable.
Which dryer brands do you see most in Clearwater?
Of 22 branded Bozmanfix dryer jobs here, GE is 32 percent, Samsung 23, Whirlpool 18, Kenmore 9 and LG 9. That is a different shape from the washers in the same houses, where no brand exceeds 21 percent – dryers get replaced independently of washers more often than people assume.
Kenmore at 9 percent marks older machines, since the brand has not been a going concern for years. GE, Whirlpool and Maytag dryer parts ride on the van, which helps first-visit fixes.
Do you charge more for a stacked washer-dryer?
The diagnostic is $150 rather than $99 on a stacked washer-dryer, because the unit has to be pulled out and separated before anything can be inspected. The same applies to a double wall oven. It is still credited against the repair when you approve the work.
Stacked and compact units are more common in Clearwater than in our inland cities, particularly in beachfront and condominium laundry rooms; single-family housing across the rest of the city takes the standard $99.
Appliances We Fix in Clearwater, FL
Five more service pages for Clearwater, each built on the jobs we have actually run here.
Appliance Repair in Clearwater – city hub, all 9 ZIP codes Serving Clearwater, FL and the wider Tampa Bay area → View our full service areaBook Dryer Repair in Clearwater
$99 diagnostic applied to the repair, $150 on stacked units, 90-day parts and labor warranty.