Washer Repair Sunrise FL
Washer repair in Sunrise runs a median of $409 once a part is replaced, with the middle half of jobs between $377 and $473. Checked against the thirteen Broward cities where we have run at least five washer repairs, that is the fourth highest in the county and well above the $370 median across our 4,763 completed washer repairs company-wide.
The explanation is the same one that puts refrigerators near the top here: this is a city where a great deal of equipment has been in service a long time, and long-serving washers do not fail at belts and lid switches. They fail at motors, transmissions and control boards.
One consequence shows up directly in our local file — Kenmore machines, a brand that no longer exists, and what that means for getting one repaired.
Washer Repair in Sunrise
Top load, front load and stacked pairs, including discontinued brands. Firm total before the work starts, and the supply hoses get looked at while the machine is out.
What a Washer Repair Costs, by Part
Each row is a median across our completed washer repairs where that component was the one replaced, with the part, the labour and the service call added together rather than a parts price with the real cost hidden behind it.
| Component replaced | Median, part and labor and call | Jobs (n) | Usual symptom |
|---|---|---|---|
| Drive belt | $341 | 74 | Drum will not turn, motor runs |
| Door lock or lid switch | $351 | 143 | Will not start, or will not spin |
| Water inlet valve | $362 | 137 | Will not fill, or fills slowly |
| Shock absorbers or suspension | $367 | 195 | Banging and walking on spin |
| Tub bearing | $380 | 11 | Roaring that rises with spin speed |
| Drain pump | $381 | 213 | Standing water, will not drain |
| Drive motor | $387 | 81 | Hums, will not turn |
| Motor control board | $436 | 163 | Error code, dead panel |
| Front-load door boot seal | $450 | 49 | Leaking at the door, mould at the fold |
By symptom the medians run $354 for leaking across 482 jobs, $362 for a machine that will not spin across 384, $372 for noise and shaking across 584, $376 for one that will not start, $377 for one that will not drain across 508, and $385 where an error code is the presenting complaint across 492.
Our own Sunrise invoices include a Maytag washer at $562, a GE washer at $496, an LG at $492 and another GE at $473. The whole city price map is on appliance repair in Sunrise.
Sunrise Washer Repair, in Figures
- 22 washer jobs on record in Sunrise, 9 of them in the last twelve months.
- Median with a part replaced: $409, middle half $377 to $473.
- That is the fourth highest washer median of the thirteen Broward cities where we have run at least five.
- Company-wide base underneath: 4,763 completed washer repairs at a $370 median, middle half $310 to $445.
- Local brands include Samsung, Maytag, Whirlpool, GE, Amana, Electrolux and Kenmore.
- Noise and shaking is the largest single washer complaint in our book, 584 jobs at a $372 median.
- The drain pump is the most replaced washer part, 213 jobs at $381, with suspension close behind at 195.
- Named local jobs: a Maytag at $562, a GE at $496 and an LG at $492.
- Sunrise Utilities treats water at three plants using three different processes, all addressing hardness.
- Diagnostic is $99, or $150 on a stacked pair, because the two machines must be separated first.
Repairing a Brand That No Longer Exists
Kenmore appears on our Sunrise file, and in a city with housing stock going back to the sixties that is entirely expected. It also produces one of the most common worries we hear: the brand is gone, so can it even be fixed? The answer is yes, and the reason is worth explaining, because it applies to several names still sitting in laundry rooms across this city.
Kenmore never manufactured washing machines. It was Sears’ house label, applied to machines built by other companies — Whirlpool for many years, and at various times Frigidaire, LG and others. The badge on the front says Kenmore. The machine underneath is a Whirlpool, an LG or a Frigidaire with a different control panel and a different model number.
That matters practically in three ways.
The parts exist. A pump, a valve, a lid switch or a transmission for a Kenmore is the same component as for the machine it was actually built from, and those are still made and stocked.
What decides availability is not the badge but the model number, which is why the full model number from the plate is the single most useful thing you can send us on a machine like this. On Kenmore that number carries a manufacturer prefix, and reading it tells a technician immediately whose machine is really in the laundry room.
The diagnosis follows the real manufacturer, not the label. A Kenmore built by Whirlpool fails the way a Whirlpool of that era fails. Anyone approaching it as an orphan appliance is working blind; anyone who identifies the underlying platform is working from a known failure list.
These machines are often worth keeping. A great many of them were built in an era of heavier frames and mechanical transmissions, and a machine that has already run for twenty years has demonstrated something about how it was made.
If the fault is a pump, a valve, a switch or a coupler, repairing it is straightforwardly better economics than replacing it. We will tell you honestly when it is not.
The same logic covers other names you may have: Amana, Maytag, Roper, Estate and Admiral all now sit under manufacturers who continue to supply parts. A discontinued badge is not a discontinued machine.
What Makes Washer Repair in Sunrise Its Own Market
Fourth in the county, and it is about age not price $409
Sunrise sits fourth of the thirteen Broward cities where we have run at least five washer repairs. That is not a local pricing decision — every job is quoted the same way everywhere. It reflects a city that began in 1961 and whose original housing is still widely occupied, with machines kept far past the point where a shorter-tenure household would have replaced them.
The cheap failures happen early in a machine’s life; the expensive ones happen late. A city full of late-life machines produces exactly this number.
Older top loaders fail differently from modern ones TRANSMISSION AND COUPLER
A modern washer is usually direct-drive: the motor turns the basket through an electronically controlled assembly. Many older top loaders are not. They use a belt or a coupler to a mechanical transmission that converts rotation into the back-and-forth agitation of a central agitator.
Those machines announce their failures in ways the modern ones do not: agitation that has gone weak or stopped while the spin still works, a loud knock at the start of each agitation stroke, or a motor that runs while nothing moves.
If your washer has a tall agitator in the middle of the tub, this is the family it belongs to, and describing which of those three you have narrows the diagnosis considerably.
Soft water means less detergent, not more THREE TREATMENT PLANTS
Sunrise Utilities draws from the Biscayne Aquifer through four well fields and treats it at three plants — lime softening at Springtree, membrane softening with ion exchange at Sawgrass, lime softening with filtration at Southwest — all of which address hardness.
The city publishes no hardness figure so we quote none, but the practical point holds: the dose printed on the bottle is generous for water treated this way, excess detergent does not rinse out, and what stays behind in the outer tub and the boot fold is the actual cause of almost every washer that smells.
Level matters more than people believe SUSPENSION AT $367
Suspension and shock absorbers are the second most replaced washer component in our book at 195 jobs, and many of those failures begin with a machine that was never levelled properly — or a floor that has moved in the decades since it was. A modern high-spin washer that rocks on one foot is not merely noisy: every spin cycle hammers the suspension, the bearings and eventually the tub.
Push down on each corner of the top with the machine empty. Any rock at all, and the feet need adjusting and the lock nuts tightening before you spend anything on parts.
Stacked pairs and tract-house laundry closets $150 DIAGNOSTIC
A stacked pair has to be separated before anything at the back of either machine can be reached, which is why the diagnostic there is $150 rather than $99 — time rather than parts, and applied to the repair in the same way. In a planned city the same closet dimensions repeat across hundreds of homes, so clearance is either fine everywhere or tight everywhere.
Say at booking whether the pair is stacked, whether the machines sit on pedestals, and whether the space is wider than the appliances, because those three details decide how long the slot needs to be.
Error codes are a starting point, not a diagnosis 492 JOBS
Error codes are the presenting complaint on 492 of our washer jobs at a $385 median, and modern machines report faults by consequence rather than cause. A drain code appears when the machine cannot reach a dry sump within a set time — which can be the pump at $381, or a sock in the filter, a kinked hose, or a partly blocked standpipe.
An imbalance code appears when the drum cannot safely reach spin speed, which can be suspension at $367 or simply a duvet bunched on one side. Write the code down when you book, because it narrows the search, but do not buy a part on the strength of it.
Washer Leaking or Not Spinning?
The supply hoses get looked at while the machine is out.
The Four Families of Washer Fault
Every washer complaint belongs to one of four groups, and placing yours before you call makes the visit shorter and the estimate firmer.
Water in. The inlet valve at $362, the supply hoses, the screens behind them, and the pressure sensor that tells the machine how full the drum is. Symptoms are a machine that will not fill, fills slowly, fills continuously, or reports a fill fault. The free check here is the screens in the valve inlets, which clog and produce a symptom identical to a failed valve.
Water out. The drain pump at $381 and everything downstream: the filter, the drain hose, the standpipe. This is the group most likely to have a free answer, because the coin trap or filter at the bottom front of most machines catches exactly what you would expect and is designed to be opened by the owner.
Rotation. The drive belt at $341, the motor at $387, the door lock or lid switch at $351, and on older top loaders the coupler and transmission as well. Symptoms are a drum that will not turn, will not agitate, will not spin, or does one but not the other. That last distinction matters most on an older machine: agitation without spin and spin without agitation point at different components.
Movement and noise. Suspension at $367, bearings at $380, and behind both the levelling. This is the largest complaint group in our book at 584 jobs. The useful split: banging only on spin and only with a heavy load is suspension or balance, while a roar that rises steadily with drum speed and is present even on a light load is a bearing.
What the Technician Checks First on a Washer
The order is designed to exhaust free answers before touching a part. First the machine is rocked at all four corners with the drum empty, because an unlevel washer explains a large share of noise, walking and imbalance complaints and takes a minute to put right with a spirit level.
Second the drain filter comes out and the drain hose is followed to the standpipe, since standing water has a free answer more often than a paid one. Third the supply hoses and valve screens are checked, both for the fill complaint and because we would rather find a hose about to fail than come back to a flood.
Fourth, on a front loader, the boot fold is pulled back and inspected all the way round, because a tear low in the boot leaks only during a wash and only from underneath, which people describe as a leak from nowhere.
On an older machine there is a fifth step: reading the model plate properly. On a Kenmore or another house-label appliance that number identifies who actually built it, which turns an unknown machine into a known platform with a known failure list and known parts.
Only then do meters come out for the lid switch, the motor and the board. Our method is set out on how technicians diagnose appliances.
One habit worth adopting before you call, whichever family your fault belongs to: note whether the problem happens on every cycle or only some.
A machine that drains on a short cycle but not a long one, spins fine on a light load and never on a heavy one, or throws a code only on hot washes is telling us something a technician standing in front of it for twenty minutes may never see.
Intermittent behaviour usually points at a component failing under load or at temperature rather than one that has failed outright, and it is a far more useful thing to report than a description of the noise. On an older machine it is often the earliest sign that a part is on its way out while it is still cheap to change.
Four Checks the Technician Runs First on an Washer
- Clean the drain filter. Bottom front corner on most front loaders behind a small hatch, and accessible on many top loaders. Put a towel and a shallow tray down first, because water will come out. A choked filter produces the same standing water as a failed pump at $381.
- Level the machine at all four corners. Empty, push down on each corner of the top. Any rock means the feet need adjusting and the lock nuts tightening. A washer that rocks destroys its own suspension over time.
- Photograph the model plate. Usually inside the lid, on the door frame, or on the back panel. On an older or house-label machine this is what tells us who really built it and whether the part is still stocked — the single biggest factor in a first-visit repair.
- Halve your detergent. Sunrise water is treated for hardness at all three of the city’s plants, so the dose on the bottle is generous here. Excess detergent does not rinse away and is the actual cause of almost every washer that smells.
Match Your Washer Symptom to the Likely Cause
- Will not start at all. Door lock or lid switch at $351, then the board. Cheap and common.
- Fills but will not agitate, spin still works. On an older top loader, the coupler or transmission. On a modern one, the drive assembly.
- Agitates but will not spin. Lid switch or door lock first, then the drain, because most machines will not spin on a full tub.
- Motor runs and nothing moves at all. Snapped belt at $341, or a failed coupler.
- Standing water in the drum. Filter and drain hose before the pump at $381.
- Banging and walking on spin. Levelling first, then suspension at $367.
- Roaring that rises with spin speed, even on a light load. Tub bearing at $380, and worth acting on early.
- Loud knock at the start of each agitation stroke. Transmission or agitator dogs on an older top loader.
- Leaking at the front of a front loader. Boot seal at $450, often torn low where coins collect.
- Leaking from the back or under the machine. Supply hoses or a hose connection. Shut the valves and book.
- Fills continuously and will not stop. Inlet valve or pressure sensor. Shut the supply valves now.
- Error code after a storm. Try five full minutes unplugged before booking a board at $436.
Repair or Replace a Washer in Sunrise
This decision goes to repair more often than the local median suggests, and the reason is that the median is being set by which faults occur rather than by how much any one repair costs.
The whole routine list runs $341 to $450 with labour and the service call already inside, and against a comparable new washer plus delivery, haul-away and installation, a single fault is not a close contest — on a stacked pair the fitting alone is real work.
That holds even on a machine that has been in service for twenty years: a pump, a valve, a lid switch, a coupler or a set of shock absorbers on an appliance that has already demonstrated two decades of life is straightforwardly good arithmetic, and several of the jobs on our Sunrise file are exactly that.
The honest exceptions are two. A tub bearing or a transmission on a machine already well past its service life is a heavy job on an appliance likely to present something else next, and we will tell you when you are in that position rather than quoting it.
And a control board at $436 on a machine that has already had a board or a motor is where the arithmetic tips. What we will not do is write a machine off for being old — the deciding question is always which component failed and whether the part is still available, which is why the model plate matters.
Typical service lives are on how long washing machines last, and the general framework on the repair versus replacement guide.
Discounts Applied Automatically
Priority Membership
$179 a year — five diagnostics, priority slots
- Five free diagnostic visits a year, a $495 value
- Priority scheduling with 24 to 48 hour response
- $30 off labor on every repair
- Extended warranty on all Bozmanfix work
What South Florida Customers Say About Bozmanfix
“Washer threw an H2O supply error, Max diagnosed and fixed it fast.”
“Alex quickly identified the problem with our washer. 10/10.”
“Max fixed my washer same day, great pricing.”
“Oleh got the exact parts I needed.”
Washer Repair in Sunrise — Questions We Get
How much does washer repair cost in Sunrise?
The median is $409 once a part is replaced, with the middle half of local jobs between $377 and $473, which is the fourth highest washer median of the thirteen Broward cities where we have run at least five.
By component the medians are $341 on a drive belt, $351 on a door lock or lid switch, $362 on a water inlet valve, $367 on shock absorbers or suspension, $380 on a tub bearing, $381 on a drain pump, $387 on a drive motor, $436 on a motor control board and $450 on a front-load door boot seal.
Every figure includes the part, the labor and the service call together.
Can you still repair a Kenmore washer if the brand is gone?
Yes, and the reason is that Kenmore never built washing machines in the first place. It was Sears’ house label applied to machines manufactured by other companies — Whirlpool for many years, and at various times Frigidaire, LG and others. The badge says Kenmore; the machine underneath is a Whirlpool, an LG or a Frigidaire with a different control panel and model number.
So the parts still exist, still stocked, and the diagnosis follows the real manufacturer’s known failure list. What decides everything is the full model number from the plate, which carries a manufacturer prefix — send it when you book and a technician can tell immediately whose machine is actually in your laundry room. The same is true of Amana, Roper, Estate and Admiral.
Why is washer repair higher here than in neighbouring cities?
Because of which faults occur, not because of local pricing — every job is quoted the same way everywhere we work. Sunrise began in 1961 as Sunrise Golf Village and much of that original housing is still occupied, with washers kept far past the point where a shorter-tenure household would have replaced them.
The cheap failures — belts, lid switches, inlet valves — happen early in a machine’s life. The expensive ones — motors, transmissions, bearings, control boards — happen late. A city full of late-life machines produces a local band that starts at $377 rather than at $310, and the individual repairs cost exactly what they cost anywhere else.
My washer fills but the agitator barely moves. What is that?
On an older top loader with a tall agitator in the middle of the tub, that is usually the drive coupler or the transmission rather than the motor. Those machines are not direct-drive: the motor turns the basket through a mechanical transmission that converts rotation into the back-and-forth agitation stroke, and there is a coupler between the two designed to fail before anything more expensive does.
The useful distinction is which function you have lost. Agitation gone with spin still working, spin gone with agitation still working, and motor running while nothing moves at all are three different faults with three different answers, so say which one describes your machine when you book.
Is my old washer worth repairing at all?
Age alone does not decide it — the component that failed does.
A pump at $381, a valve at $362, a lid switch at $351, a coupler or a set of shock absorbers at $367 on a machine that has already run twenty years is straightforwardly good arithmetic, because that machine has demonstrated something about how it was built and the repair is a fraction of a replacement plus delivery, haul-away and installation.
The two honest exceptions are a bearing or a transmission on a machine well past its service life, and a control board at $436 on one that has already had a board or motor. We will tell you plainly when you are in either of those. The genuine constraint on an old machine is part availability, which the model number settles.
There is standing water in the drum. Is the pump gone?
Check the free answers first, because on this complaint they are common. Most machines have a drain filter behind a small hatch at the bottom front, designed to be opened by the owner, and it collects coins, hairpins and screws until it chokes. Put a towel and a shallow tray down before you open it, because water will come out.
Then follow the drain hose to the standpipe and check it is not kinked or pushed too far in. If both are clear, the drain pump at $381 is the answer, and it is our most replaced washer part at 213 jobs.
Why does my washer smell, and is that a fault?
Usually it is detergent rather than a fault. Sunrise Utilities treats the city’s water at three plants using three different processes — lime softening at Springtree, membrane softening with an ion exchange system at Sawgrass, and lime softening with filtration at Southwest — and all of them address hardness, so the dose printed on the bottle is generous for water treated this way.
Excess detergent does not rinse away: it builds in the outer tub, the dispenser and the rubber boot fold of a front loader, where it becomes a slime that holds odour and transfers to clothes. Halve the dose, wipe the boot fold dry after washes, and leave the door and dispenser drawer ajar between loads.
More Appliance Repair in Sunrise
The rest of the Sunrise set, each built on the jobs we have actually run in this city.
Appliance Repair in Sunrise — the full city price mapServing Sunrise and the wider Miami area → View our full service areaNeighbouring washer coverage on the same routes: Plantation to the south east, Coral Springs to the north and Davie to the south.
Book Washer Repair in Sunrise
22 washer jobs on record in this city, on a base of 4,763 completed washer repairs. $99 diagnostic applied to the repair, hoses checked while the machine is out, 90-day parts and labor warranty.