Washer Repair in Nocatee, FL
Two Nocatee tickets sit at opposite ends of the same fault: a GE control board replaced at $605.28, and an LG power supply board repaired at $90. That $90 is the cheapest outcome anywhere in our local washer book, and it is the one we look for first — our company median for replacing a motor control board is $436, so a board that can be mended rather than swapped is a materially better result.
It is not always possible, and this page explains when. We hold 8 washer jobs across Nocatee, and the number to plan on is $370, our company median across 4,763 washer replacements, with a middle half of $310 to $445.
Washer Repair in Nocatee, FL
Will not drain, will not spin, leaking, banging on spin, or dead at the panel. Across Nocatee, the Ponte Vedra side and the Saint Augustine side, with the $99 diagnostic coming off the bill when you approve the repair.
All Five Paid Local Tickets
| Ticket | Machine | What the paperwork records |
|---|---|---|
| $605.28 | GE, Ponte Vedra side | Replacing the control board |
| $444.33 | Speed Queen, Saint Augustine side | Leaking and will not spin |
| $387.74 | Whirlpool, Ponte Vedra side | Component replaced, not itemised |
| $99.00 | GE, Ponte Vedra side | Control board replacement quoted |
| $90.00 | LG, Ponte Vedra side | Power supply board repair — the board mended, not replaced |
| $370 | Median with a part replaced, middle half $310 to $445 | Company-wide, 4,763 repairs — use this |
What Washer Repair Costs, by Component
Per-part prices are steadiest on a large base, so the rows below are company-wide across 4,763 replacements. Each figure is the part, the labor and the service call together, not the price of the component on a parts website.
| Repair | Median, full ticket | Source | Jobs (n) |
|---|---|---|---|
| Drive belt | $341 | Company-wide | 74 |
| Lid switch or door lock | $351 | Company-wide | 143 |
| Water inlet valve | $362 | Company-wide | 137 |
| Suspension rods or shock absorbers | $367 | Company-wide | 195 |
| Tub bearing | $380 | Company-wide | 11 |
| Drain pump | $381 | Company-wide | 213 |
| Drive motor | $387 | Company-wide | 81 |
| Motor control board | $436 | Company-wide | 163 |
| Front-load door boot seal | $450 | Company-wide | 49 |
| All washer jobs with a part replaced | $370 · middle half $310 to $445 | Company-wide — use this | 4,763 |
Why Nocatee Washers Fail the Way They Do
JEA draws from the Floridan aquifer about a thousand feet down, aerates the water to strip the sulphur odour that groundwater carries, then chlorinates it. There is no softening step anywhere in that process, and JEA publishes the resulting hardness by ZIP code.
The Ponte Vedra side comes back at 372 parts per million, 22 grains per gallon — the highest reading on the entire JEA table, ahead of Ponte Vedra Beach at 346, St. Johns at 305 and every ZIP in Duval County. The neighbouring Saint Augustine side reads 307 ppm. Both are classified Very Hard.
Two effects follow, and the indirect one matters more day to day. Directly, a washer inlet valve is a solenoid that opens and shuts into 372 parts per million of dissolved calcium and magnesium several times a cycle, which makes it a wear part rather than a lifetime one at a company median of $362.
Indirectly, poor lather in very hard water leads households to add more detergent, and the residue builds in the dispenser housing, the drum and around the sensors — which is where smells, marks on clothes and eventually leaks start.
A control board repaired rather than replaced $90 AGAINST A $436 COMPANY MEDIAN
A Ponte Vedra-side LG ticket reads power supply board repair at $90. That is the board mended in place rather than swapped out, and it is by a wide margin the cheapest outcome in our local washer book.
It is not always possible — a board with failed traces or a burnt-out driver needs replacing — but where the fault is a supply-side component on the board itself, repairing it beats a $436 replacement comfortably.
On a control board fault the technician tells you whether the whole board has failed or whether one part of it can be mended.
Two more local tickets name the same subsystem $605.28 AND $99
A GE on the Ponte Vedra side needed its control board replaced at $605.28 — above the company motor control board median of $436, which is what happens when a board comes with additional access or a second component. Another GE ticket in the same ZIP records a control board replacement quoted at the $99 diagnostic, where the household took the number and did not proceed on the day.
Three of five paid local washer tickets touch board work, and on modern machines the electronics are a real share of what fails, with a wide price range across them.
A Speed Queen leaking and not spinning $444.33
A Saint Augustine-side ticket is logged as SQ-WM / LEAK WONT SPIN at $444.33. Speed Queen is a commercial-grade machine sold for domestic use, built heavier and designed to be serviced, so it costs considerably more than a mainstream washer to replace and repair stays ahead of replacement far longer.
Leaking together with a failure to spin usually points at one of two places: the boot seal on a front-loader, at a company median of $450, or a drain and pump problem where the machine aborts the spin because it cannot empty.
Two untagged local tickets sit in the same family — a drain pump replacement at $434.50, and a $395 visit that cleaned the gasket and hatch glass, repaired the drain line and cleared the pump filter.
Seven of eight local washer jobs are on the Ponte Vedra side AND ALL EIGHT ARE FROM 2026
Seven of our eight washer jobs are on the Ponte Vedra side and one on the Saint Augustine side, and every one of them falls inside 2026 — the most concentrated and most current appliance sample in this area. That means these figures were set by very recent work at current parts prices.
That is why every priced row on this page is company-wide.
Control board fault? The technician tells you whether the whole board has failed or whether one part of it can be repaired. Book online or call (954) 902-6229.
Match Your Symptom to the Likely Cause
- Dead at the panel, or a cycle that will not start — the control board. One local LG had its power supply board repaired at $90; one local GE needed a full board replacement at $605.28. The technician tells you which yours needs. Company median for a motor control board is $436.
- Leaking and will not spin together — on a front-loader most often the door boot seal at $450, or a drain problem that makes the machine abort the spin. One local Speed Queen came in with exactly this at $444.33.
- Will not drain, water standing in the drum — drain pump at $381, a blocked pump filter, or a drain hose kinked or pushed too far into the standpipe. One untagged local ticket replaced a drain pump at $434.50.
- Banging or walking hard on spin — suspension rods or shock absorbers at $367. The technician checks that the machine is level and all four feet are locked first.
- Smells, or residue left on clothes — dispenser drawer and door boot. At 22 grains per gallon people over-dose detergent and the residue builds. One local job cleaned the gasket and hatch glass and cleared the pump filter at $395. See what washer error codes mean.
- Filling slowly, or on only one temperature — the inlet valve at $362. In this water that solenoid is a wear part rather than a lifetime one. See washing machine out of balance.
Where in Nocatee We See This Work
Seven of our eight washer jobs are on the Ponte Vedra side and one on the Saint Augustine side, and every one of them falls inside 2026 — the most current appliance sample in this area. Of the branded machines: GE 2, Whirlpool 1, LG 1, Speed Queen 1, Amana 1.
On a stacked washer-dryer the diagnostic is $150 rather than $99, because the two halves must be separated before anything can be inspected.
On the name: the Postal Service lists the primary city for the main Nocatee ZIP as Ponte Vedra, with Ponte Vedra Beach and Town of Nocatee both as acceptable alternates, and for the southern ZIP as Saint Augustine. Both sit in St. Johns County rather than Duval. Our own tickets split the same way: on the Ponte Vedra side, 31 are written Nocatee and 25 Ponte Vedra Beach.
We named these pages Nocatee because it is a USPS-acceptable name for that ZIP and because a separate page covers Ponte Vedra Beach, a different ZIP with a different hardness reading.
| ZIP | Washer jobs | Water hardness | Housing units |
|---|---|---|---|
| Ponte Vedra side Nocatee / Ponte Vedra | 7 | 372 ppm · 22 grains · Very Hard | 11,028 |
| Saint Augustine side Saint Augustine | 1 | 307 ppm · 18 grains · Very Hard | 20,220 |
| Both | 8 jobs, 5 paid, 3 with a part | JEA published table by ZIP | 31,248 |
Around Nocatee
Washer work in the neighbouring areas is on its own pages. East on the coast is Ponte Vedra Beach. North-west is St. Johns and Fruit Cove and beyond it Mandarin. North into Duval are Southside and the University of North Florida area, where one machine was put right by cleaning its sensors.
Then San Marco and San Jose and Arlington, where washer work is a steady line. Across the river, Riverside, Avondale and Springfield sits on pre-war timber floors where levelling matters more than parts. Up the coast are Atlantic Beach and Neptune Beach. The Nocatee set starts at the Nocatee appliance repair hub.
Repair or Replace a Washer Here
A washer repair with a part replaced runs $370 company-wide against roughly $700 to $1,200 for a mid-market replacement installed, so on anything under about eight years old the repair is straightforwardly ahead — and in largely new housing most of what we see sits inside that window.
The local book shows both edges of the range. A board repaired at $90 is a fraction of any replacement machine and the best outcome available. A board replaced at $605.28 is where the arithmetic starts to tighten on an older unit, and two major components together — a drain pump at $381 plus a board at $436 is $817 — tightens it further.
Running the other way, a commercial-grade machine like a Speed Queen costs several times a mainstream washer to replace and is built to be serviced, so repair stays ahead far longer. We put the total in front of you before anything is ordered. Framework: repair or replace guide and how long washing machines last.
Discounts Applied Automatically
Priority Membership
$179 a year — five diagnostics, priority slots
- Five free diagnostic visits a year, a $495 value
- Priority scheduling with 24 to 48 hour response
- $30 off labor on every repair
- Extended warranty on all Bozmanfix work
What Jacksonville Area Customers Say About Bozmanfix
“Showed up on time and fixed my washing machine in 45 minutes.”
“Vitalii was on time and very easy to work with. He made sure he cleaned up after his repair.”
“Vitalii fixed the problem right away, very friendly, came out same day. Great experience.”
“Denis was great and patient dealing with the 3 service calls to get our washer back up and running. Appreciate it!”
Washer Repair in Nocatee — Questions We Get
How much does washer repair cost in Nocatee, FL?
Budget $370, Bozmanfix’s company median across 4,763 washer replacements, with a middle half of $310 to $445 — parts, labor and the service call together.
By component expect roughly $341 for a drive belt, $351 for a lid switch or door lock, $362 for an inlet valve, $367 for suspension work, $381 for a drain pump and $436 for a motor control board.
Our local tickets span $90 to $605.28, and the reason for that spread is explained on this page.
Can a control board be repaired instead of replaced?
Sometimes, and the technician tells you which applies. One local Ponte Vedra-side LG ticket reads power supply board repair at $90 — the board mended in place rather than swapped, and by a wide margin the cheapest outcome in our local washer book against a company motor control board median of $436.
It is not always possible: a board with failed traces or a burnt-out driver needs replacing, and one local GE needed exactly that at $605.28. But where the fault is a supply-side component on the board itself, mending it is materially cheaper. On a board fault the technician tells you whether the whole board has failed or whether one part of it can be repaired.
My washer is leaking and will not spin. Are those the same fault?
Often, yes. A machine that cannot empty properly will abort its spin, so a drain problem shows up as both symptoms at once — and a leak from the boot seal on a front-loader can do the same by triggering a fault. One local Speed Queen came in logged exactly as leaking and will not spin, at $444.33.
The two places to look are the door boot seal, at a company median of $450, and the drain circuit: pump at $381, plus the filter and hose. Two untagged local tickets sit in that family, one replacing a drain pump at $434.50.
Does the hard water here affect my washing machine?
Directly and indirectly. JEA rates the Ponte Vedra side at 372 parts per million or 22 grains per gallon — the highest reading on its entire table — and the Saint Augustine side at 307 ppm, with no softening step anywhere in its treatment.
The direct effect is on the inlet valve, a solenoid that opens and shuts into that water several times a cycle, which makes it a wear part at a company median of $362.
The indirect effect matters more day to day: poor lather leads households to add more detergent, and the residue builds in the dispenser, the drum and around the sensors, producing smells, marks on clothes and eventually leaks. The technician looks at the dispenser drawer on the visit.
Do you service Speed Queen washers?
Yes — one of our five paid local washer tickets is a Speed Queen. It is a commercial-grade machine sold for domestic use, built heavier and designed to be serviced rather than replaced, so it costs considerably more than a mainstream washer to replace and repair stays ahead far longer than the component table alone suggests.
Tell us at booking if yours is a Speed Queen or any other commercial-grade unit, so the visit is scheduled with the right expectations and, where possible, the likely part on board.
What does the $99 diagnostic buy me?
A qualified technician with a meter on your machine, a named fault, and a firm total for the repair before any work starts or any part is ordered. The $99 then comes off that total when you approve the repair, so on a completed job the diagnostic is part of the repair price.
One local GE ticket shows the value of it plainly: a control board replacement was quoted at the diagnostic and the household took the number away to decide. The diagnostic is $150 on a stacked washer-dryer, because the two halves have to be separated before anything can be inspected.
Is my washer worth repairing?
At a Bozmanfix company median of $370 against roughly $700 to $1,200 for a mid-market replacement installed, almost always yes on a machine under about eight years old — and in largely new housing most of what Bozmanfix sees sits inside that window. Two things change the answer.
Two major components at once genuinely gets close: a drain pump at $381 plus a control board at $436 is $817. And on a commercial-grade machine such as a Speed Queen the case for repair is stronger, not weaker, because replacement costs several times a mainstream washer. We give you the total before we start.
Other Appliance Repairs in Nocatee, FL
Each page is built on its own local invoices.
Appliance Repair in Nocatee — the full picture for both sides Serving Nocatee, FL and the wider Jacksonville area → View our full service areaBook Washer Repair in Nocatee, FL
Eight washer jobs on record across both ZIPs, all from 2026. $99 diagnostic applied to the repair, 90-day parts and labor warranty.