Oven and Range Repair in Oakleaf, FL
Plan on $398 for an oven or range repair in Oakleaf once a part is replaced — the Florida median across 780 repairs, not a local figure. We have 6 oven jobs inside ZIP 32065, 5 paid and only 3 with a component replaced, which is below the line at which we will publish a local price.
There is a second reason to be careful with this sample, and it is one you will not see stated on many local pages: only 2 of those 6 jobs fall inside the last twelve months. Ovens are the one appliance in this ZIP where our volume is going down while everything else goes up, so even the little local data we have is ageing.
The Florida column below is the number to plan around.
Oven and Range Repair in Oakleaf, FL 32065
Gas or electric, freestanding range or built-in wall oven, one price across ZIP 32065. You get the total before we start and the $99 diagnostic comes off the bill when you approve the repair.
What Oven and Range Repair Costs, by Component
Two price columns, because Florida oven repairs genuinely run higher than the national figure — $398 against $380 overall — and on the most common part the gap is wide: an igniter is $352 nationally and $405 in Florida. That is not a local surcharge, it is what our Florida invoices say across 780 repairs, and you deserve the column that applies to you rather than the flattering one.
Every figure is the part, the labour and the service call together. Our three Oakleaf component jobs appear at the bottom for completeness, marked as too thin to quote from.
| Repair | Median, nationwide | Median, Florida | Jobs, nationwide (n) |
|---|---|---|---|
| Bake or broil element | $325 | $345 | 89 |
| Door hinge, latch or lock | $345 | $388 | 21 |
| Switch, knob or touchpad | $349 | $369 | 29 |
| Gas igniter | $352 | $405 | 221 |
| Temperature sensor | $357 | $300 | 12 |
| Spark module or electrode | $358 | $347 | 15 |
| Thermostat | $420 | $404 | 23 |
| Door gasket or seal | $460 | — | 11 |
| Main control board | $475 | $443 | 89 |
| All oven and range jobs with a part | $380 | $398 | 1,879 |
| All oven and range jobs with a part | Oakleaf 32065 · too thin to quote, and ageing | 3 | |
The full local list, since six is small enough to show you outright: a Whirlpool oven at $376, a second Whirlpool at $295, a Samsung range at $250, a Samsung oven at $78, and two visits settled for the $99 diagnostic — one Samsung, one Whirlpool.
Elsewhere in the ZIP, on tickets that carried no appliance tag, one job records that the igniter should be replaced at $370, and another covered a refrigerator ice dispenser drawer and an oven lower compartment drawer on the same visit. Nothing in that list contradicts the Florida figures; there simply is not enough of it to build a local price from.
Why Oakleaf Ovens Fail the Way They Do
Ovens are 6.5 percent of the 92 classified jobs we have run in 32065, against 11.7 percent company-wide, and they are the only appliance here whose call volume is shrinking rather than growing. Four of our six oven jobs are from 2024 or early 2025; two are from 2026.
Meanwhile refrigerators, washers and dryers in this same ZIP all have the large majority of their volume inside the last twelve months.
We are not going to invent a mechanism for that — six jobs will not support one — but stating it is more useful than smoothing it over, because it tells you exactly how much weight to put on the local numbers on this page. The answer is: not much, use the Florida column.
The igniter is where gas oven money goes 221 REPLACEMENTS · $405 IN FLORIDA
A gas oven igniter does two jobs at once: it glows hot enough to light the gas, and it draws enough current to open the safety valve. As it ages it keeps glowing but stops drawing full current, so the valve never opens properly and the oven either takes forever to heat or never gets there at all.
The tell is a burner glowing orange for a minute with no flame following. It is our most replaced part company-wide by a wide margin and runs $405 in Florida against $352 nationally. The same symptom can also come from the safety valve, which is a different part and a different bill — which is why we will not diagnose a gas oven over the phone.
Samsung and Whirlpool split our local oven work evenly, with no GE at all 3 AND 3
All six of our Oakleaf oven jobs carry a brand and they divide exactly: Samsung 3, Whirlpool 3. No GE appears, which is worth a raised eyebrow rather than a conclusion, because GE leads oven work company-wide at 23.6 percent ahead of Whirlpool at 21.8 and Samsung at 16.0.
Six jobs is nowhere near enough to claim GE ranges are absent from Oakleaf kitchens, and we are not claiming it. What we can say is that in this ZIP GE leads our refrigerator work and our dishwasher work but has not appeared on an oven ticket yet.
A brand table records how often we are called out, not reliability — see most reliable appliance brands.
Two of five paid visits end with a part fitted 60 PERCENT
Our Oakleaf oven part-fitted share is 60 percent, close to the company-wide oven figure of 37.3 percent, and both are above our all-appliance average of 63.1 percent. Ovens generate a lot of nothing-to-replace visits everywhere, and the usual reason is the complaint being about temperature accuracy rather than about the machine not working.
A domestic oven cycles around its setting by 25 to 30°F as a matter of normal operation, and a household that has never measured it with a thermometer can reasonably mistake that for a fault. The free test in the box below is aimed precisely at those two visits.
Tell us gas or electric, and tank or meter, at booking ORIFICES AND PRESSURE DIFFER
One job in this ZIP was an igniter, so gas cooking is here. It matters technically what kind: a propane appliance runs at higher pressure through smaller burner orifices than the same model configured for natural gas, so the regulator setting, the conversion kit and sometimes the igniter part number are different.
Telling us at booking whether you are on a tank or a meter means the technician arrives with the right parts and the right pressure gauge, which is the difference between finishing on the first visit and coming back. It makes no difference to the $99 diagnostic or to the price list.
Thermometer test done and the oven is genuinely off? Plan on $398 for a Florida oven repair with a part, and $405 if it is a gas igniter. Book online or call (954) 902-6229.
Match Your Symptom to the Likely Cause
- Gas burner or oven clicks and clicks but will not light — igniter at $405 in Florida, spark module or electrode at $347, or the safety valve. The igniter is 221 of our replacements against 15 for the spark module, so the odds sit heavily on the first.
- Electric oven will not heat at all — bake element at $345 in Florida, or the control board at $443. Look at the element with the oven cold: a visible break, blister or bright spot is a failed element and a same-visit repair.
- Heats, but nowhere near the setting — temperature sensor at $300 in Florida, or the thermostat at $404. Do the thermometer test first, because a 25 to 30°F cycle is normal and not a fault.
- Broil works but bake does not, or the other way round — the failed one of the two elements, or the relay on the board driving it. The cleanest diagnosis on an electric oven, because the working half proves the supply and the controls are fine.
- Door will not close properly, heat escaping around it — hinge or latch at $388 in Florida, or the door gasket at $460 nationally. A door that will not seal makes a perfectly good thermostat look badly out.
- Display dark or nonsensical while the machine has power — control board at $443 in Florida. Cut the breaker for two minutes first; a latched fault sometimes clears and it costs nothing to try.
Where in Oakleaf We See This Work
All six oven jobs are in ZIP 32065, and every work order is written Orange Park because that is the only city name the Postal Service accepts for this postcode — even though the Census counts 31,034 people here under the name Oakleaf Plantation.
Which page you want depends on your ZIP: 32065 is this one. If your ZIP is 32073, the incorporated town of Orange Park four miles south-east, you want oven repair in Orange Park, a separate cluster with a healthier local sample — six component jobs there giving $411, against three here.
One price across the whole of 32065 with no travel surcharge. Two equipment notes: a double wall oven carries a $150 diagnostic rather than $99, because both cavities have to be pulled and separated before either can be assessed, and if your hob is a separate cooktop rather than part of a range, say so at booking. Coverage detail on the Oakleaf appliance repair hub.
Repair or Replace, in Florida Numbers
A Florida oven repair with a part replaced runs $398, against roughly $700 to $1,400 for a mid-market freestanding range installed and considerably more for a built-in wall oven, where replacement means matching a cabinet opening that may no longer exist in current standard sizes.
On a machine under about ten years old the repair is straightforwardly the better buy, and ovens tend to outlast other appliances because the mechanical stress on them is low. Company-wide, that decision splits close to even on ovens, close to our all-appliance average of 36.9 percent.
The case that genuinely turns is a control board at $443 on a range past twelve years, particularly a gas range that has already had its igniter done once. On a built-in wall oven the arithmetic almost always favours repair, because the cabinet is the expensive part of a replacement rather than the appliance. Framework: repair or replace guide.
Discounts Applied Automatically
Priority Membership
$179 a year — five diagnostics, priority slots
- Five free diagnostic visits a year, a $495 value
- Priority scheduling with 24 to 48 hour response
- $30 off labor on every repair
- Extended warranty on all Bozmanfix work
What Customers Say About Our Oven and Range Work
“Denis was timely, in fact early, efficient, nice, professional and extremely helpful. I had someone else incorrectly diagnose the oven in my cupcake shop and never show up for the repair. Denis came in same day and found the issue.”
“Found a way to fix it. Impressed, as it was not easy.”
“Denis did an amazing job. Thank you to the whole team.”
“Did a great job. Prompt, courteous.”
Oven Repair in Oakleaf — Questions We Get
How much does oven repair cost in Oakleaf, FL?
Plan on $398, the Florida median once a part is replaced across 780 oven repairs, parts and labor and the service call together. We deliberately do not publish a local Oakleaf figure: we have only three component jobs in ZIP 32065 and four of our six oven jobs here are from 2024 or early 2025, so the sample is both too small and too old.
By component in Florida: temperature sensor $300, bake element $345, spark module $347, switch or touchpad $369, door hinge $388, thermostat $404, gas igniter $405, control board $443. Nationwide the overall figure is $380.
Why are there so few oven jobs in this ZIP?
We do not know, and we would rather say that than guess. Ovens are 6.5 percent of our classified work in 32065 against 11.7 percent company-wide, and they are the only appliance here whose volume is falling — two of six jobs inside the last twelve months, while refrigerators, washers and dryers all have most of their volume in that window.
Six jobs is far too few to support a theory. What it does support is a practical decision, which is to plan from the Florida figures rather than from three local invoices.
Do you charge to calibrate an oven?
No, and we do not offer one, because it is not a real service on our price list. If your oven runs hot or cold, what we actually fix is a failed temperature sensor at $300 in Florida, a failed thermostat at $404, or a door that no longer seals.
Test it free first: oven thermometer on the middle rack, set to 350°F, read 20 minutes after the preheat light goes out. A 25 to 30°F swing either side of the setting is normal cycling. You get a firm price for the whole job before any work begins, and the $99 comes off it when you approve the repair.
My gas oven clicks but will not light. What is it?
Most likely the igniter, which is our most replaced part company-wide at 221 replacements and runs $405 in Florida. A gas oven igniter has to glow hot enough to light the gas and draw enough current to open the safety valve; as it ages it keeps glowing but stops drawing full current, so you get an orange glow and no flame.
One job in this ZIP was logged exactly as the igniter needing replacement. The same symptom can come from the safety valve, or on a cooktop burner from the spark module at $347, which is why we will not quote it over the phone.
What do I pay if the oven does not need a part?
In Oakleaf, 2 of 5 paid oven visits, which is 40 percent and close to the company-wide oven figure of 37.3 percent. Ovens produce a lot of nothing-to-replace visits everywhere, and the usual reason is that the complaint is about temperature accuracy rather than the machine failing.
A domestic oven cycles 25 to 30°F around its setting as normal operation. The free thermometer test on this page is aimed precisely at that, and it costs you nothing to run before booking.
Which oven brands do you see in Oakleaf?
All six of our local oven jobs carry a brand and they split evenly: Samsung 3, Whirlpool 3. No GE has appeared on an oven ticket here yet, which is notable only because GE leads oven work company-wide at 23.6 percent, and because GE does lead our refrigerator and dishwasher work in this same ZIP.
Six jobs is far too small a sample to conclude anything about what is in Oakleaf kitchens, and we are not concluding it. This reflects how often we are called to a brand, not how reliable it is.
Is your range on propane or natural gas?
Tell us at booking, because it changes what the technician brings. A propane appliance runs at higher pressure through smaller burner orifices than the same model configured for natural gas, so the regulator setting, the conversion kit and occasionally the igniter part number are different.
Getting that right at booking is the difference between finishing on the first visit and returning with the correct part. It makes no difference to the $99 diagnostic or to the price list.
Is it worth repairing, or should I replace it?
At $398 in Florida with a part replaced against roughly $700 to $1,400 for a mid-market freestanding range installed, repair wins on any machine under about ten years old, and ovens tend to last longer than other appliances because the mechanical stress on them is low.
On a built-in wall oven the case is stronger still, because replacing one means matching a cabinet opening that may not exist in current standard sizes. Where it turns is a control board at $443 on a range past twelve years that has already had an igniter done. Company-wide that decision splits close to even on ovens.
Appliance Repair Services in Oakleaf, FL
Five more service pages for ZIP 32065, each built on the local jobs behind it.
Appliance Repair in Oakleaf — cluster hub, all of 32065 Serving Oakleaf, FL and the wider Jacksonville area → View our full service areaBook Oven and Range Repair in Oakleaf, FL
Six oven and range jobs on record in ZIP 32065 and honest Florida figures for the rest. $99 diagnostic applied to the repair, $150 on a double wall oven, 90-day parts and labor warranty.