Dishwasher Repair Canton GA
Dishwasher repair in Canton, GA has a median cost of $320 once a part is replaced, and $286 across every completed visit — the lowest price band of any appliance we service in this city. That comes from 50 dishwasher jobs inside the two Canton ZIP codes for 48 households, 46 of which closed as paid work, with a middle half of $282 to $377 and only 2 visits above $500.
The local record has a detail worth pulling out before anything else: of the four Canton dishwasher invoices that name what was actually done, three cost $225 or less and none of them replaced a major component. A drain line cleaned at $200, a set of bracket adjusters at $200, a Bosch control board reset at $225.
The fourth was a vent assembly and water inlet hose together at $351. On this appliance, in this city, the work is often service and adjustment rather than parts — and there is a reason for that which comes straight from the water supply.
Dishwasher Repair in Canton, GA
Standing water in the bottom, will not start or will not latch, dishes coming out gritty or filmed, water under the kickplate, not drying, a grinding or humming noise, or an error code on the panel. Both Canton ZIP codes, total confirmed before the work starts.
What a Dishwasher Repair Costs, by the Part That Failed
Thirty-two local repairs cannot honestly price nine separate components, so the table below is built from 2,684 completed dishwasher jobs across our whole service area. Every figure is the full ticket — the part, the labor and the service call added together. A dishwasher is the cheapest of the major appliances to keep running, and the table shows why: the entire common range spans about $140.
| What failed | Median total | Jobs (n) |
|---|---|---|
| Spray arm | $283 | 12 |
| Door latch or door switch | $312 | 28 |
| Door gasket or seal | $330 | 42 |
| Water inlet valve | $340 | 37 |
| Drain pump | $350 | 273 |
| Heating element | $362 | 40 |
| Circulation motor | $374 | 122 |
| Control board | $387 | 93 |
| Detergent dispenser | $423 | 27 |
Now the local record, with one quirk of this city’s paperwork stated up front.
Our Canton technicians wrote good notes but often left the appliance tag off — 47 percent of all jobs here carry no appliance tag — so some component detail sits outside the tagged dishwasher file. Inside it, four invoices name the work: a Frigidaire that needed the vent assembly and the water inlet hose replaced together at $351, a Samsung that needed bracket adjusters at $200, a Frigidaire whose drain line was cleaned out at $200, and a Bosch whose fix was resetting the PCB board at $225. Two more record a completed repair without naming the part, a Whirlpool at $325 and a GE at $386, which sit right on the local median.
We have also excluded from every figure on this page a $978 diagnostic-fee line, a $390 new-dishwasher installation and five manufacturer recall visits, because none of those is a repair and leaving them in would quietly inflate the numbers you are reading.
Canton Dishwasher Repair in Figures
- Across 46 paid dishwasher visits in Canton, GA (ZIP codes 30114 and 30115), the median completed visit was $286 and the median repair with a part replaced was $320, including parts, labor and the service call.
- The middle half of those repairs ran $282 to $377, and only 2 of the 46 paid visits exceeded $500.
- Of the 4 Canton dishwasher invoices that name the work performed, three were $225 or less: a drain line cleaned at $200, bracket adjusters at $200 and a control board reset at $225. The fourth replaced a vent assembly and water inlet hose at $351.
- Company-wide, across 2,684 completed dishwasher repairs, the median drain pump repair is $350 (n=273), a circulation motor is $374 (n=122) and a control board is $387 (n=93).
- Across 416 company-wide dishwasher jobs reported as not draining, the median completed repair was $325; for 331 reported as leaking it was $340 and for 112 reported as not cleaning it was $348.
- Cherokee County water is 16 mg/L as calcium carbonate, which the county Water and Sewerage Authority classifies as very soft against a hardness threshold of 100 mg/L — so scale is not a working cause of dishwasher failure in Canton.
Those figures come from our own completed-job record across 66,161 service visits, reported as medians rather than averages with the sample size beside each one. Writers and researchers covering appliance repair costs in Cherokee County are welcome to cite them, and if you need a different cut of the data you can ask us for it.
Very Soft Water Removes the Usual Villain
Almost everything written about dishwashers assumes hard water. Cloudy glassware, a chalky film on the tub, scale baked onto the heating element, a spray arm whose holes have closed up — those are the standard complaints, and in most of metro Atlanta we cannot tell you whether they apply, because the utilities do not publish a hardness figure.
Cherokee County is the exception. The Water and Sewerage Authority publishes it directly: water above 100 mg/L as calcium carbonate is defined as hard, and Cherokee County’s water is 16 mg/L, which the Authority itself describes as very soft. The raw water comes from the Etowah River, which runs east to west through the middle of Canton, treated at a facility expanded to an operable 38 million gallons a day and backed by the Lathem drought contingency reservoir.
That single fact rewrites the advice for this appliance. Descaling tablets, dishwasher salt and citric-acid rinses solve a problem Canton does not have, and a water softener bought to protect a dishwasher here protects it from nothing.
What replaces scale as the local cause of filmed dishes is the opposite mistake: soft water needs markedly less detergent than the dose on the box assumes, and the excess does not rinse away. It leaves a fine grey or bluish film on glasses and on the inside of the door, and people reasonably read that film as hard-water scale and buy more products to fight it, which makes it worse.
If your complaint is filmed or gritty dishes rather than a mechanical fault, halve the detergent for a fortnight and use rinse aid rather than more powder. Company-wide the not-cleaning complaint still resolves at a $348 median across 112 jobs when it is genuinely mechanical — usually a blocked spray arm or a tired circulation motor — but on this route it is worth ruling out the free explanation first.
One caveat that matters here more than in a compact suburb: the 16 mg/L figure belongs to the county system, and these two ZIP codes cover 168 square miles between them, much of it rural. CCWSA reports serving more than 225,000 people against a county estimated at 299,273, so a meaningful number of Canton addresses are on a private well.
If you are on a well, none of the reasoning above is yours — well water in the county can be considerably harder, and only a test tells you what you have. Say so when you book and the technician will look at the element and the spray arms with that in mind.
Why Canton Dishwashers Fail the Way They Do
The cheapest major appliance in the city to keep $320
At a $320 median with a part and a middle half of $282 to $377, the dishwasher is the lowest price band of the six appliances we cover in Canton — below the washer at $345, the dryer at $365, the refrigerator at $384 and the oven at $420.
Only 2 of 46 paid visits went past $500 and the largest was $743.
The reason is that a dishwasher has no expensive single component: company-wide the spread from a spray arm at $283 to a detergent dispenser at $423 is only $140, and the two parts that do most of the work — the drain pump at $350 and the circulation motor at $374 — sit in the middle of it.
Against a new machine of comparable specification plus delivery, fitting, plumbing and haul-away of the old one, that makes the repair decision on this appliance the most clear-cut in the kitchen.
It is also why we will happily come out for a dishwasher that is merely annoying rather than dead — a filmed load or a slow drain is usually a cheap fix rather than the beginning of the end. Pricing is set out on how appliance repair pricing works.
Three of four named local jobs were service, not parts $200 · $200 · $225
The four Canton invoices that record what was actually done tell you something the price table cannot. A Frigidaire had its drain line cleaned out at $200. A Samsung needed its bracket adjusters replaced at $200 so the door would latch square. A Bosch was fixed by resetting the PCB board at $225.
Only the fourth, a Frigidaire needing the vent assembly and the water inlet hose together, involved real parts at $351.
That pattern is genuinely typical of this appliance: the common faults are blockage, alignment and a latched electronic error, and all three are cheap when caught before they cascade. A drain line left blocked makes the pump run against resistance until it fails, at which point the $200 clean becomes a $350 pump.
A door that does not latch square wears its own seal. And an electronic fault that has latched will often clear on a proper power cycle — worth knowing, because you can try that yourself: switch the machine off at the breaker or unplug it, wait five full minutes so the board actually drains, then restore power. More on control electronics is in control board and smart appliance repair.
Standing water is a drain problem long before it is a pump problem $325 · $350
Water left in the bottom of the tub at the end of a cycle is the single most common dishwasher complaint we take, and company-wide it resolves at a $325 median across 416 jobs, with the drain pump at $350 across 273.
What makes it worth a phone call rather than a panic is that the drain path has three cheap failure points before it has an expensive one. The filter in the floor of the tub blocks first.
Then the drain hose, which needs a high loop under the counter to stop dirty water siphoning back and must not be crushed where the machine was pushed into its cavity. Then the disposal connection: if a garbage disposal was fitted after the dishwasher, the knockout plug inside its inlet has to be removed, and if it was not, the dishwasher cannot drain at all.
Only after those three is the pump itself the answer — one Canton machine needed nothing more than the drain line cleaning out, at $200. The walkthrough is on why a dishwasher will not drain.
A GE and Whirlpool city with a real Bosch presence GE 13 · WHIRLPOOL 11 · BOSCH 5
Brand tags across our 50 Canton dishwasher jobs run GE 13, Whirlpool 11, Bosch 5, Frigidaire 4, Maytag 3, Samsung 3, then one KitchenAid and one LG.
The GE and Whirlpool weight is what you would expect in houses built between 2000 and 2015, and their parts — pumps, latches, valves, boards — are common enough to ride on the van, which is why a same-visit finish is realistic on those.
The five Bosch machines are the interesting part of this file. Bosch builds quiet, and quiet means the pump and the electronics are packaged low and tight under the tub with more insulation around them, so access takes longer than on an American machine even when the part is ordinary.
Their parts are also more often ordered rather than carried, so on a Bosch the number to ask for before approving anything is the lead time, and you will be given it. One local Bosch was put right by resetting the board, at $225. Brand context is on the most-serviced appliance brands.
Built under a counter, which is where the labor goes $99 FLAT
A dishwasher is the only kitchen appliance that is simultaneously plumbed, wired and bolted into cabinetry, and that is where the labor in every figure on this page actually sits. To reach a pump or a motor the machine comes out of its cavity with the water supply and the drain still attached, usually after the countertop brackets are unscrewed and the kickplate is off.
The service fee is a flat $99 regardless — there is no built-in surcharge on a dishwasher, unlike a stacked washer-dryer or a double wall oven where the $150 fee applies. That $99 is applied to the repair the moment you approve the work.
Two things help the visit go in one trip: clear the cabinet under the sink so the drain and supply connections are reachable, and if the machine is a slide-in fitted tight against stone or tile, mention it when you book.
A machine wedged under a quartz overhang sometimes needs the counter edge protected before it will come out, and knowing in advance means the right kit arrives with the technician.
Two ZIP codes, one price list $293 VS $328
We cover 30114 and 30115 at the same prices with no travel surcharge, and both carry Holly Springs as a postal alias.
On dishwashers, 30114 on the west and north side gives us 26 jobs with 18 repairs at a $293 median, and 30115 on the east and south side gives us 24 jobs with 14 repairs at a $328 median. A $35 gap on samples of eighteen and fourteen is two invoices either way, not a finding, and we will not dress it up as one.
The geography behind it is real: 30114 covers 95.2 square miles of land plus 6.6 square miles of water where the county runs down to Lake Allatoona and the Etowah backwater, and 30115 covers 73.2 square miles out toward Hickory Flat.
Forty-eight separate Canton households appear in this file, which is close to one per job — dishwashers are the appliance people call about once and then not again for years, and that is a good sign rather than a thin dataset.
🚚 Canton is a standing route, not a special trip, and common GE, Whirlpool, Frigidaire and Maytag dishwasher parts ride on the van — so same-day is realistic if you call before noon.
Match Your Symptom to the Likely Cause
- Standing water in the bottom at the end of the cycle — the filter, the drain hose loop, the disposal knockout plug, then the drain pump at $350 company-wide across 273 jobs. Company-wide the whole complaint resolves at a $325 median across 416 jobs, and one Canton machine needed only the drain line cleaned, at $200. See dishwasher will not drain.
- Dishes come out gritty, sandy or with food redeposited — start with the filter in the floor of the tub and the spray arm holes. If those are clear it is the circulation motor at $374 or a blocked spray arm at $283. Company-wide the not-cleaning complaint is a $348 repair across 112 jobs.
- Glasses come out with a grey or bluish film — on 16 mg/L water this is almost always too much detergent rather than scale. Halve the dose, add rinse aid, and give it a fortnight before booking anything.
- Water under the kickplate or on the floor in front — the door gasket at $330, the inlet valve at $340, or a hose connection. One Canton job replaced the vent assembly and the water inlet hose together at $351. Company-wide leaks resolve at a $340 median across 331 jobs.
- Will not start, or the panel lights but nothing happens — the door latch or switch at $312, or misaligned brackets so the door cannot close square; one Canton machine needed bracket adjusters at $200. Try a full five-minute power cycle at the breaker first, because a latched board fault will sometimes clear — one local Bosch needed exactly that, at $225.
- Dishes are clean but soaking wet — the heating element at $362, or the rinse-aid dispenser empty. Company-wide the not-drying complaint is a $360 repair across 33 jobs, and on a machine that air-dries by design it may be behaving normally.
- Grinding, humming or a rattle during the wash — usually something hard that has got past the filter into the pump housing, sometimes the circulation motor bearing. Company-wide noise complaints resolve at a $380 median across 93 jobs. Worth catching early, because a fragment circulating in the pump wears the impeller.
- Detergent left undissolved in the door cup — the dispenser at $423 company-wide, or simply cold water reaching the machine too slowly. Run the kitchen tap hot before starting a cycle and see whether it clears.
Repair or Replace, on the Canton Numbers
This is the clearest of the six decisions in a Canton kitchen. The local median with a part is $320, the middle half is $282 to $377, and only 2 of 46 paid visits went past $500.
Against a comparable new dishwasher plus delivery, fitting, the plumbing and electrical connection and haul-away of the old machine, repair wins on virtually anything that is not physically broken — and the reason is structural rather than a matter of opinion: a dishwasher has no single component whose failure costs a large fraction of the machine. Company-wide the dearest common part, the detergent dispenser, is $423, and the two hardest-working parts, the drain pump and the circulation motor, are $350 and $374.
Nine to twelve years is the normal service life, and the three faults that dominate this city’s record — a blocked drain line, a door that will not latch square, a board holding a latched error — are not end-of-life failures at all.
The one case worth putting numbers side by side on is a machine past ten years where the tub or the door seal channel itself has corroded, because that is the part nobody replaces.
Service-life detail is in how long dishwashers last and the wider comparison in the repair versus replacement guide.
Discounts Applied Automatically
Priority Membership
$179 a year — five diagnostics, priority slots
- Five free diagnostic visits a year, a $495 value
- Priority scheduling with 24 to 48 hour response
- $30 off labor on every repair
- Extended warranty on all Bozmanfix work
What Atlanta Customers Say About Bozmanfix
“Max from Bozmanfix came out about 3 hours after our first call and had the dishwasher apart and then fixed within 45 mins.”
“Very professional work. We called for a dishwasher repair and it was done within just a few days. Eugene was prompt and speedy, and made sure to keep our space tidy.”
“Denis was absolutely wonderful. He took the time to thoroughly inspect my dishwasher and give his diagnosis. Repair was done within the next day quickly and efficiently.”
“In and out! I’m so glad. I tried to fix the dishwasher myself and I wish I called sooner.”
Dishwasher Repair in Canton — Questions We Get
How much does dishwasher repair cost in Canton, GA?
The median is $320 once a part is replaced and $286 across every completed visit, from 46 paid dishwasher jobs inside the two Canton ZIP codes. The middle half of repairs runs $282 to $377 and only 2 of the 46 paid visits went above $500, which makes this the lowest price band of any appliance we service in the city.
By component, company-wide across 2,684 completed dishwasher repairs and including the part, the labor and the service call: spray arm $283, door latch or switch $312, door gasket $330, water inlet valve $340, drain pump $350, heating element $362, circulation motor $374, control board $387, detergent dispenser $423.
There is water standing in the bottom of my dishwasher. What is it?
The drain path, and it has three cheap failure points before it has an expensive one. First the filter cylinder in the floor of the tub, which twists out by hand on almost every machine built since about 2010 and blocks long before anything else.
Second the drain hose under the sink, which needs a high loop up against the underside of the counter and must not be crushed behind the machine. Third, if a garbage disposal was fitted after the dishwasher, the knockout plug inside the disposal inlet has to have been removed, and a new disposal with the plug still in place will stop a dishwasher draining completely.
Only after those is the drain pump itself the answer, at $350 company-wide across 273 jobs. One Canton machine needed nothing more than the drain line cleaned out, at $200.
Does hard water damage dishwashers in Canton?
Not on the county system, and this is one of the few places where the utility publishes the actual figure. Water above 100 mg/L as calcium carbonate counts as hard; Cherokee County water is 16 mg/L, which the Water and Sewerage Authority itself calls very soft.
The raw water comes from the Etowah River. That means descaling tablets, dishwasher salt and a softener sold to protect the machine are all solving a problem you do not have. What does cause filmed glasses here is the opposite mistake: soft water needs much less detergent than the dose on the box assumes, and the excess leaves a grey or bluish film that looks exactly like scale.
Halve the dose and use rinse aid. One caveat: with 168 square miles across these two ZIP codes, plenty of addresses are on a private well, where the water can be considerably harder and only a test will tell you.
My dishwasher will not start at all. What should I try first?
Two things, in this order. Press the door firmly shut and listen for the latch to click, because a dishwasher will not begin a cycle it cannot confirm the door is closed on, and door hardware is a real local fault: one Canton machine needed bracket adjusters at $200 so the door would sit square.
Then do a full power cycle: switch the machine off at the breaker or unplug it, wait five whole minutes so the control board actually drains, and restore power.
Modern boards latch fault states and will sometimes hold one until they are properly reset — one Canton Bosch was fixed by exactly that, at $225. If neither works, the door latch or switch is $312 company-wide and the control board is $387.
Why are my dishes coming out gritty when the cycle finishes?
Almost always water not reaching them with enough force, and the first two causes are free to fix. Twist out the filter cylinder in the floor of the tub and rinse the mesh under a tap; a blocked filter starves the circulation pump and produces exactly the symptoms of a failing one.
Then take out the lower spray arm and check that the holes are open, spinning it by hand to be sure it turns freely. If both are clear, it is mechanical: a blocked or cracked spray arm at $283 company-wide, or a tired circulation motor at $374.
Company-wide the not-cleaning complaint resolves at a $348 median across 112 jobs. Also worth knowing on this route: a grey film on glassware is detergent rather than grit, and that one is a dosing fix.
Is it worth repairing a dishwasher or should I replace it?
On the Canton numbers, repair is the clearest case in the kitchen. The local median with a part is $320 and the middle half is $282 to $377, against a new machine of comparable specification plus delivery, fitting, the plumbing and electrical connection and haul-away of the old one.
Structurally there is no single dishwasher component whose failure costs a large fraction of the machine: company-wide the dearest common part is the detergent dispenser at $423, and the two hardest-working parts are the drain pump at $350 and the circulation motor at $374.
Nine to twelve years is the normal service life, and the faults that dominate our Canton record — a blocked drain line, a door not latching square, a board holding a latched error — are not end-of-life failures.
The one case where we would put the two numbers side by side is a machine past ten years where the tub itself or the seal channel has corroded.
Is there an extra charge because the dishwasher is built in?
No. The service fee on a dishwasher is a flat $99 and it is applied to the repair the moment you approve the work. The $150 fee applies to a stacked washer-dryer and to a double or wall oven, where the machine has to be unstacked or drawn out of a cabinet before it can be opened, and it is always on the quote before any work starts.
Two things make a dishwasher visit go in one trip: clear the cabinet under the sink so the drain and water connections are reachable, and mention it when you book if the machine is fitted tight against stone or tile, since a unit wedged under a quartz overhang sometimes needs the counter edge protected before it will come out.
More Appliance Repair in Canton, GA
Each page is built on the jobs we have actually run in this city, with the local price band and the failure patterns for that appliance.
Appliance Repair in Canton GA — all services and city pricingServing Canton, GA and the wider Atlanta area → View our full service areaBook Dishwasher Repair in Canton
50 dishwasher jobs on record in this city across 48 households, a $320 median once a part is replaced and a middle half of $282 to $377. $99 diagnostic applied to the repair, 90-day parts and labor warranty.