Ice Maker and Freezer Repair in Indian Trail and Monroe, NC

🧊 4 Local Ice Maker and Freezer Jobs 📉 No Local Price — Two Component Invoices 💰 Company Figures: Ice Maker $415 · Freezer $385 🔧 Both Local Component Jobs Came In Near $215 🛡️ 90-Day Parts and Labor Warranty

Ice maker and freezer repair in Indian Trail and Monroe runs a company-wide median of $415 for ice maker work and $385 for freezer work, parts and labour and the service call together. Those are company figures, used deliberately.

Our whole record in ZIP codes 28079 and 28110 is 4 ice maker and freezer jobs, two of them paid and both involving a replaced part — at $210 and $220.

Two invoices is not a median. They are worth printing anyway, because they are the two cheapest ice and freezer jobs in our entire Charlotte book, and a page that quoted $415 without showing them would be hiding something.

Ice Maker and Freezer Repair — Indian Trail 28079 and Monroe 28110

Refrigerator ice makers, standalone and undercounter ice machines, chest and upright freezers. Freezer calls get priority scheduling because food loss is on the clock. The $99 diagnostic is applied to the repair when you approve it.

What Ice Maker and Freezer Repair Costs

Every figure below is company-wide and every one is the part, the labour and the service call together — the number on your bill rather than the price of a component on a parts website. There is no local column, because with two component invoices we would be publishing an average of two numbers.

Ice maker work rests on 2,091 completed repairs and freezer work on 2,269, which is what a median needs behind it. Our two local invoices appear in the box below so you can see the whole local record on one page.

RepairMedian, full ticketSourceJobs (n)
Ice maker — frozen fill tube$393Company-wide40
Ice maker — defrost heater or timer$415Company-wide70
Ice maker — water inlet valve$428Company-wide69
Ice maker — evaporator or condenser fan$432Company-wide60
Ice maker — water filter changed on the visit$440Company-wide79
Ice maker — module or assembly$449Company-wide57
Ice maker — control board$488Company-wide32
All ice maker jobs with a part replaced$415Company-wide2,091
Freezer — defrost heater or timer$364Company-wide203
Freezer — door gasket$389Company-wide77
Freezer — thermostat or sensor$390Company-wide81
Freezer — evaporator or condenser fan$396Company-wide135
Freezer — control board$494Company-wide51
Freezer — compressor$700Company-wide107
All freezer jobs with a part replaced$385Company-wide2,269
Our two local component jobs$210 and $22028079 · 28110 — printed, not averaged2
Visit settled on the spot$99Flat rateApplied to the repair
💡 Both local invoices came in near $215, which is barely above the $200 line where we count a job as having had a part replaced at all. Every other ice and freezer component job in our Charlotte book runs $294 or higher. Two jobs cannot establish a pattern and we are not claiming one — but they are a fair reminder that not every no-ice call is a $400 repair, and that the diagnosis is what decides.

The gap between $215 and the company median of $415 is the whole reason we diagnose before quoting. On this appliance one symptom — no ice — can come from a frozen fill tube at $393, a water inlet valve at $428, an ice maker module at $449, a control board at $488, or from something at the light end that costs a fraction of any of them.

There is no way to know from the outside of the cabinet, and there is no honest way to quote it over the phone. What we can tell you when you book is which of the three machines you have, because that changes the visit: a refrigerator ice maker, a standalone or undercounter ice machine, or a freezer.

Why Indian Trail and Monroe Ice Makers and Freezers Fail the Way They Do

Four jobs, and we are labelling it rather than dressing it up TWO COMPONENT INVOICES

Ice makers and freezers together are 4.9 percent of the 81 classified jobs in these two ZIP codes, against 3.3 percent company-wide, so proportionally this area sends us slightly more of this work than average — but four jobs is four jobs. Three are in 28079 and one in 28110.

Both paid visits ended with a part replaced. That is the entire local record and it is on this page in full, which is the only honest way to present a sample this size.

The freezer has the highest part-fitted share of any appliance we service 56.1 PERCENT COMPANY-WIDE

Across our company book, 56.1 percent of paid freezer visits end with a part fitted — higher than washers at 59.0 percent, dishwashers at 40.7 and ovens at 37.3.

The usual causes are mundane and free to check: a door held fractionally open by a packed shelf, a gasket that is dirty rather than failed, a thermostat knocked while loading, or a unit in an unheated garage where the surrounding air is colder than the range the thermostat was designed for. That last one is common in detached housing like this and it is design rather than failure.

The ice maker is the most expensive category we service $415 COMPANY MEDIAN

Across our whole book, ice maker work carries the highest median of any appliance category at $415 — above refrigerators at $394, freezers at $385, washers at $370 and dishwashers at $338. Ice making combines three systems in one small box: a water circuit that can freeze or scale, a refrigeration circuit that can lose charge, and electronics controlling both.

One symptom, no ice, can come from any of them, and the diagnosis is what separates a $393 fill tube from a $488 control board. This is the appliance where paying to diagnose before ordering parts saves the most money.

Both branded local units are freestanding Frigidaire 2 OF 4

Two of the four local jobs name a brand and both are Frigidaire freestanding units. Across town in the SouthPark ZIP codes, all four branded ice and freezer jobs were built-in or specialty machines — a Scotsman, a U-Line, a Thermador and a KitchenAid.

Two tiny samples pointing in opposite directions, and they match the rest of each cluster: this area runs to mainstream freestanding appliances whose parts ride on the van.

This is a record of what we are called to, not a reliability ranking — that question is on most reliable appliance brands.

Tell us at booking whether it is a refrigerator ice maker, a standalone ice machine or a freezer. Freezer calls get priority scheduling. Book online or call (252) 629-9832.

Ice Maker and Freezer Work by ZIP Code

ZIPIce and freezer jobsAll appliances in this ZIPHousing unitsLand area
28079 Indian Trail310214,93546.6 sq mi
28110 Monroe14020,817127.4 sq mi
Both414235,752174.0 sq mi

Housing unit counts and land areas come from zip-codes.com; the job counts are ours. Four jobs across two ZIP codes is a record rather than a distribution, printed so you can see exactly how much sits behind this page.

It changes nothing about the service: an ice maker or freezer call from either ZIP code is handled on the same terms, at the same price list, with the same $99 diagnostic, the same priority scheduling on freezer work and the same 90-day parts and labour warranty.

It simply means the prices here come from our national book rather than from your ZIP code, and we would rather say that than imply a precision we do not have.

Where in the Cluster We See This Work

These two ZIP codes hold 92,367 people and 35,752 housing units across 174 square miles of Union County, the only part of our Charlotte coverage outside Mecklenburg. 28110 alone covers 127 square miles, making it the largest ZIP code we work in anywhere around the city, and both carry more than one accepted name — the Postal Service allows Lake Park for 28079 and Unionville for 28110.

For an ice or freezer call, two practical notes: say when you book if the freezer is full, because food loss moves the job up the queue, and if the unit is a standalone or undercounter ice machine, clear access to its water supply and drain saves real time. Coverage for all six machines is on the Indian Trail and Monroe hub.

Match Your Symptom to the Likely Cause

  • No ice at all, refrigerator otherwise fine — frozen fill tube at $393, water inlet valve at $428 or the ice maker module at $449. Check the freezer is actually at 0°F first: an ice maker in a compartment running warm will not cycle, and that is a refrigerator fault. See the refrigerator page.
  • Ice arriving slowly, or cubes small and hollow — restricted water supply, a filter past its interval, or the inlet valve. A filter change carried out on a service visit runs $440 company-wide, which is why replacing it yourself on schedule is the cheapest maintenance in the kitchen.
  • Ice tastes wrong or smells of the freezer — the filter again, or a door seal letting air move through the compartment. Neither is expensive, and both are the symptoms people put up with longest.
  • Standalone ice machine making no ice, or leaving a puddle — the drain, the water circuit, or the sealed system. Give us the brand and model at booking so the part can travel with the technician.
  • Freezer not freezing but the light comes on — defrost heater or timer at $364, an evaporator fan at $396, or a sensor at $390. Cheapest first: check nothing on a shelf is holding the door fractionally open.
  • Frost building on the walls or the food — a door gasket at $389 or the defrost circuit. A gasket that is merely dirty can be cleaned for nothing and it is worth trying when you book.
  • Running constantly and still warm — condenser blocked, fan failed, or the sealed system and the compressor at $700. Pull the unit out and look at the coils first: dust imitates a failing compressor exactly.
four checks the technician runs first. One: put a thermometer inside for a few hours — the target is 0°F, and a compartment running warmer will stop an ice maker cycling. Two: check the door closes fully against a clean gasket, with nothing on a shelf holding it a few millimetres open. Three: if the freezer lives in a garage or an outbuilding, which is common in this part of the county, check the manufacturer ambient rating — many units will not hold temperature when the surrounding air is very cold, and that is design rather than failure. Four: clear the condenser coils. Company-wide, 56.1 percent of paid freezer visits end with a part fitted, and these four checks are why.

Which Units We Are Called To Here

Two of the four local jobs carry a brand and both are Frigidaire freestanding units. We are not going to build a market share from two work orders.

What is worth setting alongside them is the rest of this cluster, where the sample is real: 88 branded jobs across all six machines, led by Whirlpool 27, Maytag 13, Samsung 13 and GE 12, with a light premium layer of four KitchenAid, three Electrolux and two Bosch.

That is a mainstream suburban brand profile with a thin premium edge — more premium than our northwest Charlotte cluster, far less than SouthPark, where the same ice and freezer category produced a Scotsman, a U-Line, a Thermador and a KitchenAid. The practical consequence here is that most parts ride on the van and most repairs finish on the first visit.

Repair or Replace, in Union County Numbers

The answer splits cleanly by machine type. A chest or upright freestanding freezer costs roughly $400 to $900 to replace, so at a company median of $385 with a part replaced the repair is close to a coin-toss — and it genuinely tips toward replacement when the diagnosis is a compressor at $700, where company-wide the decision on that work splits close to even.

A refrigerator ice maker is not a standalone decision at all: it is one component of a machine worth several times the repair, so at $415 the repair almost always wins. A built-in or undercounter ice machine is the clearest case for repairing, because replacement means matching a cabinet opening, a water supply and a drain.

Our framework is the repair or replace guide, with expected service life in how long freezers last.

Discounts Applied Automatically

$30 OFFVeteransEvery repair
$30 OFFSeniorsEvery repair
$20 OFFNew CustomersFirst repair

Priority Membership

$179 a year — five diagnostics, priority slots

  • Five free diagnostic visits a year, a $495 value
  • Priority scheduling with 24 to 48 hour response
  • $30 off labor on every repair
  • Extended warranty on all Bozmanfix work

What Customers Say About Our Ice Maker and Freezer Work

★★★★★

“Excellent service. The broken Ice Maker works now. Stepan is a delight to work with.”

— James Wieder · Verified Google review
★★★★★

“Sam was amazing. Fixed my water dispenser and ice maker in less than 30 minutes.”

— Diana Rosario · Verified Google review
★★★★★

“Great service. Completed the ice maker repair in the mentioned timeline with exact diagnosis.”

— Kamlesh Chhabria · Verified Google review
★★★★★

“Max was very professional and informative as to the problem with our ice maker.”

— Des O’Donohoe · Local Guide

Ice Maker and Freezer Repair in Indian Trail and Monroe — Questions We Get

How much does ice maker or freezer repair cost in Indian Trail and Monroe?

Use our company-wide figures: $415 median for ice maker work across 2,091 repairs and $385 for freezer work across 2,269, parts and labour and the service call together. We publish no local median because our whole record in these two ZIP codes is four jobs, two of which involved a replaced part — those two were $210 and $220.

By component, company-wide: ice maker fill tube $393, defrost $415, inlet valve $428, fan $432, filter change $440, module $449, board $488; freezer defrost $364, gasket $389, sensor $390, fan $396, board $494 and compressor $700.

Your two local jobs were about $215. Why quote $415?

Because two invoices cannot predict the third. Both of ours came in barely above the $200 line where we count a job as having had a part replaced at all, and every other ice and freezer component job in our Charlotte book runs $294 or higher.

Quoting $215 as a local price would set an expectation we could not keep. The company medians rest on 4,360 completed repairs between them, and the honest position is to give you those and print our two local numbers alongside so you can see both.

My refrigerator has stopped making ice. Is that this page or the refrigerator page?

Either, and it makes no difference to the price or the booking. The ice maker inside a refrigerator is the most common version of this call and it is routine work with parts that travel on the van — frozen fill tube at $393, inlet valve at $428, module at $449.

When you book, check the freezer is holding 0°F with a thermometer, because an ice maker sitting in a compartment that is running warm will not cycle, and that is a refrigerator fault rather than an ice maker one.

My freezer is in the garage and it is not holding temperature. Is it broken?

Possibly not. Many freezers have a minimum ambient temperature rating, and in a cold garage or outbuilding the thermostat can stop calling for cooling because the surrounding air is already below its trigger point — the compartment then warms even though nothing has failed. Check the manufacturer rating for the model before booking.

If the unit is rated for garage use and still will not hold 0°F, the likely faults are the defrost circuit at $364, an evaporator fan at $396 or a sensor at $390.

What do I pay if the freezer does not need a part?

Company-wide, 56.1 percent of paid freezer visits end with a part fitted, ahead of washers at 59 percent and dishwashers at 40.7. Locally we have two paid visits and both ended with a part replaced, which is far too small a base to quote as a rate.

The usual causes are a door held fractionally open by a packed shelf, a dirty rather than failed gasket, a knocked thermostat, or a unit in a cold garage operating outside its rated range.

My ice tastes bad. Is that a repair?

Usually not. The most common causes are a water filter past its interval and a door seal letting air circulate through the compartment, and both are maintenance rather than failure. A filter changed during a service visit runs $440 company-wide, which is a lot of money for a part you can fit yourself in five minutes — so check the filter date before booking anything.

If the filter is current, the seal is clean and the taste persists, the water line or the supply itself is worth a look.

Is a freezer compressor worth replacing?

On a freestanding chest or upright freezer, usually not. Company median for freezer compressor work is $700 across 107 repairs, against roughly $400 to $900 for a replacement unit, and across 458 visits diagnosed as a failed compressor, the decision splits close to even. On a built-in freezer drawer or an integrated column the answer reverses, because replacing means matching a cabinet opening and paying for fitting.

We put the number in front of you at the door, before you have spent anything beyond the diagnostic.

How quickly can you reach a freezer call here?

Freezer calls get priority over every appliance except a refrigerator that has stopped cooling, because food loss is on the clock, so say when you book if the freezer is full. Same-day is realistic if you call early in the day.

Distance is the one variable: 28110 covers 127 square miles, so an address out toward Unionville carries a wider arrival window than one near the centre of Indian Trail. That affects your slot, not your bill — there is no travel surcharge anywhere in the cluster.


Book Ice Maker or Freezer Repair in Indian Trail or Monroe

Refrigerator ice makers, standalone and undercounter ice machines, chest and upright freezers across 28079 and 28110. Freezer calls get priority scheduling. $99 diagnostic applied to the repair, 90-day parts and labour warranty.

Book online Call us
Book online Call us